1997 Ford F 250 HD Differential Parts
Image
Product
Price
- 35 Spline; 1.50 in. Axle Shaft Diameter; Full Float Only; Rear 10.25 in./10.5 in.
- Detroit Truetrac® Differential; 35 Spline; 1.50 in. Axle Shaft Diameter; Full Float Only; Rear 10.25 in./10.5 in.;
- Detroit Truetrac® Differential
-
Features:
- Helical Gear Limited Slip Differential
- Optimized Torque Bias Ratios Deliver Max Acceleration And Handling
- Automatic Engagement
- Works In Forward And Reverse
- Ideal For Most Vehicles
- Durable
- Smooth
- Quiet Operation
- No Special Lubrication Or Friction Modifiers Needed
- The Detroit Truetrac is a helical-gear style, limited-slip differential that maximizes wheel traction and enhances driving characteristics. Maintenance-free, it features smooth, automatic operation in forward and reverse. Its versatility makes Detroit Truetrac the ideal traction solution for almost any type of vehicle.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1997 - Ford F-250 HD | Rear |
- Auburn Gear Ected Max Differential
- Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down
- Auburn Gear Ected Max Differential; Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down;
- Auburn Gear Ected Max
-
Features:
- Selectable Full Locker And Limited Slip In One Unit
- Can Be Engaged/Disengaged At Any Reasonable Speed
- Smooth Quiet Operation
- Can Be Use With Or Without Lockout Hubs
- Made From 9310 Heat Treated Billet Steel
- Backed By 1 Year Warranty
- Covered w/4 Year Differential-Replacement Exchange
- Made In The USA
- The ECTED Max is a selectable traction device; an on/off switch is mounted near the driver. When off–the clutch pack,located behind the side gear provides the limited slip mode. As torque increases, the separating forces within the differential gears increase, causing the clutch pack to be compressed and thereby providing bias torque to the high traction wheel–your performance limited slip differential action. When selected on, current is sent to the electromagnetic coil. The coil is retained by a clip that fits over one of the bearing cap bolts, making it non-rotational. The coil rides on a ball bearing. The ball bearings spin with the differential case. The coil creates a magnetic flux so that the pilot cone is pulled into engagement with the differential case. This frictional engagement causes the bearing balls to ride up on a ramp machined into the side gear. This radial travel of the balls also causes lateral movement of the side gear. This applies a force onto the center block. The center block has an elongated hole that the center pin fits through, allowing it to float. The center block applies force to the opposite side gear, compressing the clutch pack giving the user a solid axle assembly–the spool/locker performance you desire at the strip/off-road. ECTED Max gearing is made from aircraft quality, 9310 heat-treated billet steel. Tough as nails! ECTED Max can be switched on or off on the fly, at any road speed. ECTED Max does not have any shift forks or pins that must be lined up to obtain locker mode. ECTED Max is quiet. Good-bye to noisy lockers! ECTED Max is backed by industry-leading 1 year warranty, like all Auburn Gear Performance Differentials. ECTED Max is backed by the industry-exclusive program. D-REX=Differential–Replacement EXchange Program. ECTED Max can be used in front axle applications–with or w/out lockout hubs. ECTED Max is the only selectable locker offering both limited slip and locker modes. Forget the rest-go with the best!
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1997 - Ford F-250 HD | Rear |
Showing 1 - 2 of 2 products
Loading...