1969 Porsche 911 Air and Fuel Delivery Parts
Choose your Part Name for your 1969 Porsche 911
Air Filter
Carburetor Repair Kit
Carburetor Throttle Ball Joint
Electric Fuel Pump
Engine Air Intake Hose
Fuel Filler Neck Flap
Fuel Filter
Fuel Filter Washer
Fuel Injection Thermal / Time Switch
Fuel Injector
Fuel Tank
Fuel Tank Body Seal
Fuel Tank Sending Unit
Fuel Tank Sending Unit Gasket
Throttle Lever
Throttle Rod Bushing
Image
Product
Price
- For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;CARB E.O. D-550-34
- Electric Fuel Pump; For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;
- Electric Fuel Pump
- Product Attributes:
- Hose Size: 0.3125 In.
- Maximum PSI: 3.5
- WARNING CA Proposition 65: Yes
- Fuel Type: Gasoline
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Inlet Size: 0.125 In. Npt
- Free Flow GPH: 28
- Item Weight: 1.200 Lbs.
-
Features:
- Solid-state Worry Free Electronics
- Internal Pressure Regulating
- Universal Design Allows For Easy Installation
- No Diaphragms Or Mechanical Parts To Wear Out
- They Make An Excellent Fuel Transfer Pump
- Gravity fed type pump with simple two-wire design. Works on 12 Volt negative ground systems only. Includes fittings and mounting hardware along with easy to follow DIY instructions. Pumps require approximately one amp average draw at maximum delivery. Flow rate is 28 gallons per hour (GPH) at 2 to 3-1/2 pounds per square inch (PSI). Universal design for most import 4 & 6-cylinder carburetor applications. Please see part #12S for V8 gasoline applications, part #12D for diesel applications or part #12E for Ethanol, Methanol, E85 and Race Fuel applications. Solid-state worry free electronics. Eliminates vapor lock and flooding. Works well as a fuel transfer, booster, or stand-alone pump. Not recommended for diesel, methanol, ethanol, E85 or race fuel applications!!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Sub Model | CID |
|---|---|---|---|---|---|
| 1969 - Porsche 911 | H | 1991 | 6 Cyl 2.0L | T | 122 |
- For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;CARB E.O. D-550-34
- Electric Fuel Pump; For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;
- Electric Fuel Pump
- Product Attributes:
- Hose Size: 0.3125 In.
- Maximum PSI: 3.5
- WARNING CA Proposition 65: Yes
- Fuel Type: Gasoline
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Inlet Size: 0.125 In. Npt
- Free Flow GPH: 28
- Item Weight: 1.200 Lbs.
-
Features:
- Solid-state Worry Free Electronics
- Internal Pressure Regulating
- Universal Design Allows For Easy Installation
- No Diaphragms Or Mechanical Parts To Wear Out
- They Make An Excellent Fuel Transfer Pump
- Gravity fed type pump with simple two-wire design. Works on 12 Volt negative ground systems only. Includes fittings and mounting hardware along with easy to follow DIY instructions. Pumps require approximately one amp average draw at maximum delivery. Flow rate is 28 gallons per hour (GPH) at 2 to 3-1/2 pounds per square inch (PSI). Universal design for most import 4 & 6-cylinder carburetor applications. Please see part #12S for V8 gasoline applications, part #12D for diesel applications or part #12E for Ethanol, Methanol, E85 and Race Fuel applications. Solid-state worry free electronics. Eliminates vapor lock and flooding. Works well as a fuel transfer, booster, or stand-alone pump. Not recommended for diesel, methanol, ethanol, E85 or race fuel applications!!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Sub Model | CID |
|---|---|---|---|---|---|
| 1969 - Porsche 911 | H | 1991 | 6 Cyl 2.0L | T | 122 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Rubber
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Cork
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Accelerator Cable bellcrank on transmission
- Bellcrank on Transmission.
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
- Cable & Rod Pivot Pedal
- (2 Req. Nylon, 8.5/12mm)
- Brass
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Tank to Body
Additional Fitment Information:
| Vehicle |
|---|
| 1969 - Porsche 911 |
Showing 1 - 10 of 27 products
Loading...