1988 BMW 325is Air and Fuel Delivery Parts
Choose your Part Name for your 1988 BMW 325is
Air Filter
Electric Fuel Pump
Fuel Filter
Fuel Hose
Fuel Injection Air Flow Meter Boot
Fuel Injection Idle Air Control Valve Hose
Fuel Injection Pressure Regulator
Fuel Injection Pressure Regulator O-Ring
Fuel Injection Throttle Body Coolant Heater Flange
Fuel Injection Throttle Body Cover
Fuel Injector
Fuel Injector Seal
Fuel Pump Module Assembly
Fuel Pump Relay
Fuel Pump Tank Seal
Fuel Tank Cap
Fuel Tank Sending Unit
Fuel Tank Sending Unit Gasket
Throttle Rod Bushing
Image
Product
Price
- Locking Fuel Cap
- Vented Black Cap
- Locking
- Product Attributes:
- Vented: Yes
- Lockable: Yes
- Tethered: No
- Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
This Part Fits the Following OEM/Substitute Numbers:
10582, 11582, 12F14L, 31761, 40782, 5782, 703-1841, 9MGC782, G782, MGC782, MGC782SK, P5782
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1988 - BMW 325is | L | 2494 | 6 Cyl 2.5L | 152 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Original
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- 7.5 x 3.5mm
- O-Ring 7.52mm x 3.53mm
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 3.0 Bar
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 58.8 x 4.2mm
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
- The alternate Bosch PN 69 695(PUMP ONLY) will only work with cars that were originally equipped with a Bosch pump. Some late models came with a Delco pump which is NOT interchangeable. This pump is a complete assembly with suction tubes and pick-up screen. If equipped with Delco pump as original equipment, then this complete assembly is required. This pump assembly uses 62 16 8 782 015 for O-ring.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - BMW 325is |
Showing 1 - 10 of 31 products
Loading...