2013 BMW 135is Air and Fuel Delivery Parts
Choose your Part Name for your 2013 BMW 135is
Image
Product
Price
- Fuel Pump Module Assembly
- Product Attributes:
- California Proposition 65: Warning: This Product Can Expose You To Chemicals Including Lead, Which Is Known To The State Of California To Cause Cancer And Birth Defects Or Reproductive Harm. For More Information Go To Www.p65warnings.ca.gov.
- Fuel Filter Included: No
- Connector Gender: Female
- Voltage: 12
- Negative Ground: No
- Grade Type: Regular
- In Tank or External: In Tank
- Mounting Hardware Included: No
- Fuel Type: Gas
- Gasket Or Seal Material: Nitrile Rubber
- Fuel Tank Pressure Sensor Included: No
- Minimum Pressure: 44
- Outlet Quantity: 2
- Inlet Type: Strainer
- Installation Warnings: No
- Resistance Ohms Empty: 50
- Average Flow Rating: 50
- Lock Ring Included: No
- Average Current Draw: 10
- Maximum Pressure: 97
- Pump Type: Electric
- Resistance Ohms Full: 1000
- Wire Harness Included: No
- Fuel Sending Unit Included: Yes
- Pump Design: Turbine
- Connector Quantity: 2
- Outlet Outside Diameter: 0.375
- Terminal Quantity: 2
- Gasket Or Seal Included: Yes
- Internal Or External Strainer: Internal
- Terminal Type: Pin
- Terminal Gender: Male
- Regulator Included: Yes
- Strainer Included: Yes
- Outlet Type: Quick Connect
-
Features:
- Instructional installation sheets included in every box
- Always be sure to check and clean fuel tank to avoid returns
- Each part undergoes testing to ensure the same fit, form, and function as the OE
- Sparta, distributed by the only OE full-line fuel supplier Delphi, is specifically designed for higher mileage and earlier model vehicles. Turn to the brand backed by the OE experts, who know fit and performance better than anyone.
This Part Fits the Following OEM/Substitute Numbers:
16 11 7 159 162, 16 14 7 163 298, 228235018007Z, A30326, C0651M, E8688M, M2496366, P76486M, SP5009M, USEP8688M
Additional Fitment Information:
| Vehicle | Block | CC | Engine Designation | Engine | CID |
|---|---|---|---|---|---|
| 2013 - BMW 135is | L | 2979 | N55B30A | 6 Cyl 3.0L | - |
- Fuel Cap
- Non-Vented Black Cap
- Standard
- Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
This Part Fits the Following OEM/Substitute Numbers:
1078-290971, 10844, 16116754492, 16116756772, 16117222391, 31848, 3C0201550B, 3C0201550G, 3C0201550N, 3C8201550A, 3C8201550E, 40844, 4G0201550F, 4G0201550L, 4G0201550M, 561201550A, 561201550B, 5C0201550T...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2013 - BMW 135is | L | 2979 | 6 Cyl 3.0L | - |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Direct Injection
- with EU5 Fuel Injectors and with Bosch High-Pressure Fuel Pump
- IMPORTANT: Per BMW Service Bulletin S1 B13 03 15 the injectors in the vehicle may not match what is listed in the BMW ETK. Identify the injector installed in the vehicle using ISTA / D 4.04 or later test plan using the following path: Vehicle Management - Service Functions - Powertrain - Engine Electronics - Injector Determination. Test Plan will state "This engine requires EU# Injectors" - Also Required: (1) 13 53 7 577 649 Decoupling Element
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Primary
- with O-Ring
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2013 - BMW 135is | Right |
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Multi Port Injection
- with EU5 Fuel Injectors and with Continental High-Pressure Fuel Pump
- IMPORTANT: Per BMW Service Bulletin S1 B13 03 15 the Injectors in the vehicle may not match what is listed in the BMW ETK. Identify the injector installed in the vehicle using ISTA / D 4.014 or later test plan using the following path: Vehicle Management - Service Functions - Powertrain - Engine Electronics - Injector Determination. Test Plan will state "This engine requires EU# Injectors" - Also Required: (1) 13 53 7 577 649 Decoupling Element
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Multi Port Injection
- with EU6 Fuel Injectors
- IMPORTANT: Per BMW Service Bulletin S1 B13 03 15 the injectors in the vehicle may not match what is listed in the BMW ETK. Identify the injector installed in the vehicle using ISTA / D 4.04 or later test plan using the following path: Vehicle Management - Service Functions - Powertrain - Engine Electronics - Injector Determination. Test plan will state "This engine requires EU# Injectors" - Also Required: (1) 13 53 7 577 649 Decoupling Element
- EU6 Injector
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - BMW 135is |
Showing 1 - 10 of 20 products
Loading...