2008 Acura RDX Driveline and Axles Parts
Choose your Part Name for your 2008 Acura RDX
Image
Product
Price
- Wheel Bearing
- Install Identical to OE
- National 510092 Wheel Bearing
- Product Attributes:
- Design: Double Row Angular Contact
- Width (Inch): 1.732
- Outer Race Outside Diameter (Inch): 3.583
- Outer Race Outside Diameter (MM): 91.000
- Inner Race Bore (Inch): 2.008
- Inner Race Width (MM): 44.000
- Footnote: Gen1
- Inner Race Width (Inch): 1.732
- Outer Race Width (Inch): 1.732
- Outer Race Width (MM): 44.000
- Bore (Inch): 2.008
- Inner Race Bore (MM): 51.000
- Outside Diameter (Inch): 3.583
- Part Description: Wheel Bearing
- Designed to meet or exceed OE quality, premium-quality bearings from National® are manufactured to exacting standards to deliver lasting performance and extended bearing life.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
051-4187, 44300-SJK-J01, 44300-STK-951, FW97, WB000011, WB000012
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- This bearing is equipped with an internal ABS sensor magnet. Care must be taken during installation on vehicles with ABS to insure that the sensor magnet is located on the correct side of the bearing housing. Failure to do so may cause a malfunction in the ABS system. For more info, refer to the factory service information or check with your local dealer.
- Front
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Front |
Additional Fitment Information:
| Vehicle |
|---|
| 2008 - Acura RDX |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Carrier bearing for inboard axle half shaft assembly.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Carrier bearing for inboard axle half shaft assembly.
Additional Fitment Information:
| Vehicle |
|---|
| 2008 - Acura RDX |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Rear |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 2008 - Acura RDX |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 34.7 x 54 x 9mm
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Left Inner |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 34.7 x 54 x 9mm
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2008 - Acura RDX | Rear Inner |
Showing 1 - 10 of 28 products
Loading...