1988 Mercedes Benz 260E HVAC Parts
Choose your Part Name for your 1988 Mercedes-Benz 260E
A/C Clutch Relay
A/C Compressor
A/C Condenser
A/C Evaporator Core
A/C Evaporator Drain
A/C Expansion Valve Core
A/C Line O-Ring
A/C Manifold Gasket
A/C Manifold Seal Kit
A/C Vacuum Actuator
Ambient Air Temperature Sensor
Automatic Temperature Control Switch
Cabin Air Filter
HVAC Blower Fan Sensor
HVAC Blower Motor
HVAC Control Module
HVAC Heater Case Drain Hose
HVAC Heater Control Valve
HVAC Heater Hose
HVAC Pressure Switch
Image
Product
Price
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- At Receiver-Drier Located on receiver drier for auxiliary cooling fan. Identified by 2 spade terminals on short pigtail with red base.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- For Additional Blower
- Located on receiver drier for auxiliary cooling fan. Identified by 2 spade terminals on short pigtail with red base.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- At Receiver-Drier Located on receiver drier for auxiliary cooling fan. Identified by 2 spade terminals on short pigtail with red base.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- For Compressor
- 2 bar low pressure and 30 bar high pressure binary switch. This switch is designed to be compatible with R-12 and R134a refrigerants. Located on reciever-drier with 2 spade terminals. Used for compressor cut-out.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 2 bar low pressure and 30 bar high pressure binary switch. This switch is designed to be compatible with R-12 and R134a refrigerants. Located on reciever-drier with 2 spade terminals. Used for compressor cut-out.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Eng: 12-030733-, ACC Temperature Sensor - Blue Air conditioning "OFF" emergency switch : 130 degrees Celsius : Depending on model, may be located in air intake manifold or water intake pipe.
- two prong
Additional Fitment Information:
| Vehicle | Engine Range |
|---|---|
| 1988 - Mercedes-Benz 260E | 12-030733 and up |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Eng: 10-015305-, ACC Temperature Sensor - Blue Air conditioning "OFF" emergency switch : 130 degrees Celsius : Depending on model, may be located in air intake manifold or water intake pipe.
- two prong
Additional Fitment Information:
| Vehicle | Engine Range |
|---|---|
| 1988 - Mercedes-Benz 260E | 10-015305 and up |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
- 2 bar low pressure and 30 bar high pressure binary switch. This switch is designed to be compatible with R-12 and R134a refrigerants. Located on reciever-drier with 2 spade terminals. Used for compressor cut-out.
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Mercedes-Benz 260E |
Showing 1 - 10 of 36 products
Loading...