2003 Mitsubishi Lancer Lexus Parts
Choose your Part Name for your 2003 Mitsubishi Lancer
A/C Compressor Temperature Switch
A/C Condenser Fan Assembly
A/C Line O-Ring Kit
A/C Receiver Drier
A/C Refrigerant Hose
ABS Wheel Speed Sensor
Accessory Drive Belt
Accessory Drive Belt Idler Pulley
Accessory Drive Belt Tensioner Assembly
Accessory Drive Belt Tensioner Pulley
Air Cleaner Assembly
Air Filter
Air Intake Kit
Alignment Camber Kit
Alternator
Anti-Theft Relay
Automatic Temperature Control Switch
Automatic Transmission Control Solenoid
Automatic Transmission Differential Bearing
Automatic Transmission Oil Pump Seal
Automatic Transmission Output Shaft Seal
Automatic Transmission Speed Sensor
Axle Nut
Back Up Light Bulb
Back Up Light Switch
Brake Bleeder Screw
Brake Drum
Brake Fluid
Brake Hydraulic Hose
Brake Light Bulb
Brake Pedal / Clutch Pedal Pad
Brake Pedal Pad
CV Axle Assembly
CV Joint Boot Kit
Cabin Air Filter
Car Cover
Cargo Carrier
Cargo Holder
Catalytic Converter
Catalytic Converter Gasket
Center High Mount Stop Light Bulb
Clutch Flywheel
Clutch Master Cylinder
Clutch Release Bearing
Clutch Release Bearing and Slave Cylinder Assembly
Clutch Slave Cylinder
Crankshaft Angle Sensor Blade
Differential Carrier Bearing
Direct Ignition Coil
Direct Ignition Coil Boot
Disc Brake Caliper
Disc Brake Caliper Repair Kit
Disc Brake Kit
Disc Brake Pad Set
Disc Brake Rotor
Dome Light Bulb
Drive Axle Shaft Seal
Drum Brake Hardware Kit
Drum Brake Shoe
Drum Brake Wheel Cylinder
Electric Fuel Pump
Emission Check Valve
Engine Balance Shaft Belt
Engine Balance Shaft Belt Tensioner
Engine Camshaft Follower
Engine Camshaft Position Sensor
Engine Camshaft Seal
Engine Coolant / Antifreeze
Engine Coolant Outlet O-Ring
Engine Coolant Pipe O-Ring
Engine Coolant Reservoir
Engine Coolant Reservoir Hose
Engine Coolant Temperature Sender
Engine Coolant Temperature Sensor
Engine Coolant Temperature Switch
Engine Coolant Thermostat
Engine Coolant Thermostat Housing Gasket
Engine Cooling Fan
Engine Cooling Fan Blade
Engine Cooling Fan Controller
Engine Cooling Fan Motor
Engine Cooling Fan Shroud
Engine Core Plug
Engine Crankcase Breather Hose
Engine Crankshaft Lock Key
Engine Crankshaft Position Sensor
Engine Crankshaft Pulley
Engine Crankshaft Pulley Bolt
Engine Crankshaft Seal
Engine Crankshaft Seal Retainer
Engine Cylinder Head Bolt
Engine Cylinder Head Gasket
Engine Cylinder Head Gasket Set
Engine Harmonic Balancer
Engine Intake Manifold Gasket
Engine Intake Valve
Engine Mount
Engine Oil Drain Plug
Engine Oil Drain Plug Gasket
Engine Oil Filler Cap
Engine Oil Filler Cap Gasket
Engine Oil Filler Cap O-Ring
Engine Oil Filter
Engine Oil Filter Adapter Gasket
Engine Oil Line Washer
Engine Oil Pan
Engine Oil Pressure Switch
Engine Oil Pump Pickup Tube Gasket
Engine Oil Pump Seal
Engine Timing Belt
Engine Timing Belt Roller
Engine Timing Belt Tensioner
Engine Timing Belt Tensioner Adjuster
Engine Timing Belt Tensioner Pulley
Engine Timing Cover
Engine Timing Cover Gasket
Engine Timing Idler
Engine Valve Cover Bolt O-Ring
Engine Valve Cover Gasket
Engine Valve Stem Oil Seal
Engine Variable Valve Timing (VVT) Solenoid Seal
Engine Water Pump
Engine Water Pump Gasket
Engine Water Pump Seal
Exhaust Gas Recirculation (EGR) Vacuum Delay Valve
Exhaust Gas Recirculation (EGR) Valve
Exhaust Gas Recirculation (EGR) Valve Control Solenoid
Exhaust Gas Recirculation (EGR) Valve Gasket
Exhaust Manifold Gasket
Exhaust Muffler
Exhaust Muffler Gasket
Exhaust Pipe Connector Gasket
Exhaust Pipe Flange Gasket
Exhaust Pipe to Manifold Gasket
Exhaust System Kit
Exterior Multi-Purpose LED
Flood Light
Floor Mat Set
Fog Light
Fog Light Bulb
Fog Light Relay
Fuel Filler Neck
Fuel Filter Kit
Fuel Injection Fuel Rail Insulator
Fuel Injection Idle Air Control Valve
Fuel Injection Pressure Regulator O-Ring
Fuel Injection Pressure Sensor
Fuel Injection Throttle Body Mounting Gasket
Fuel Injector O-Ring
Fuel Injector Seal
Fuel Pump Housing
Fuel Pump Relay
Fuel Pump Strainer
Fuel Pump Tank Seal
Fuel Tank Cap
Fuel Tank Pressure Sensor
Fuel Tank Sending Unit Gasket
HVAC Auxiliary Fan Control Module
HVAC Blower Motor Resistor
HVAC Blower Motor Resistor Connector
HVAC Mode Door Lever Link
HVAC Pressure Switch
Headlight Assembly
Headlight Bulb
Headlight Conversion Kit
Headlight Relay
Headlight Wiring Harness
Heated Seat Relay
Hood Light Pod
Horn Relay
Ignition Lock Cylinder
Ignition Switch
Intercooler
Interior Accent Light
Jounce Bumper
Keyless Entry Transmitter Battery
Lateral Arm
License Plate Light Bulb
Light Bar
Manifold Absolute Pressure Sensor
Manual Transmission Differential Bearing
Manual Transmission Drive Axle Seal
Manual Transmission Input Shaft Seal
Manual Transmission Mount
Manual Transmission Output Shaft Seal
Masking Film
Mud Flap
Multi-Purpose Relay
Oxygen Sensor
Parking Brake Shoe
Parking Light Bulb
Power Steering Cooler
Power Steering Filter
Power Steering Pressure Hose
Power Steering Pump
Power Window Motor
Power Window Motor and Regulator Assembly
Rack and Pinion Assembly
Rack and Pinion Bellows
Rack and Pinion Bushing
Rack and Pinion Mount Bushing
Radiator
Radiator Cap
Radiator Coolant Hose
Radio Wiring Harness
Roof Rack
Secondary Air Injection Solenoid
Serpentine Belt
Side Marker Light Bulb
Side Window Deflector
Spark Plug
Spark Plug Tube Seal
Spark Plug Wire Set
Spark Plug and Coil Wire Boot Set
Spoiler
Starter Motor
Starter Relay
Steering Bump Steer Assembly
Steering Tie Rod End
Sunroof Deflector
Suspension Ball Joint
Suspension Control Arm
Suspension Control Arm Bushing
Suspension Control Arm and Ball Joint Assembly
Suspension Shock Absorber
Suspension Shock Absorber Bellows
Suspension Shock Absorber Mount
Suspension Shock Absorber Mounting Kit
Suspension Stabilizer Bar Bushing
Suspension Stabilizer Bar Link
Suspension Stabilizer Bar Link Bushing
Suspension Stabilizer Bar Link Kit
Suspension Strut
Suspension Strut Bellows
Suspension Strut Hardware Kit
Suspension Strut Mount
Suspension Strut and Coil Spring Assembly
Suspension Trailing Arm Bushing
Tail Light Bulb
Throttle Position Sensor
Trailer Brake Control
Trailer Hitch
Trailer Wire Converter
Transfer Case Output Shaft Seal
Transmission Clutch Kit
Transmission Clutch Pressure Plate
Turbocharger Gasket
Turbocharger Inlet Gasket
Turbocharger Oil Line Gasket
Turbocharger Outlet Gasket
Turn Signal Light Bulb
Underbody Light Kit
Vapor Canister
Vapor Canister Filter
Vapor Canister Purge Solenoid
Vapor Canister Vent Solenoid
Vehicle Battery
Vehicle Speed Sensor
Vehicle-Mounted Spotlight
Washer Fluid Reservoir
Wheel Accent Light
Wheel Bearing
Wheel Bearing and Hub Assembly
Wheel Hub
Wheel Lug Nut
Wheel Lug Stud
Window Defroster Relay
Window Regulator
Window Shade
Windshield Wiper Blade
Image
Product
Price
- Spark Plug Platinum TT
- Gap 0.040 Platinum TT - Twin-Tip Technology Design with Platinum Center Electrode and Titanium Enhanced Ground Strap
- Spark Plug Platinum TT
- Platinum TT
- Product Attributes:
- Hex Size: 16.0
- Reach: 19.00
- Center Electrode Tip Material: Platinum
- Seat Type: Flat
- Ground Electrode Tip Design: Titanium Enhanced Twin-tip
- Center Electrode Core Material: Copper
- Ground Configuration: Twin-tip
- Pre-Gap Size: 1.0
- Resistance: 5000
- Ground Electrode Core Material: Nickel
- Twin-Tip design enables faster flame propagation for more complete combustion.
-
Suggested Purchase Quantity: 8
- Most jobs typically require 8 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0000-18-BP01, 0000-18-F287, 0000-18-JE41, 0000-18-KJ13, 003 159 31 03, 003 159 54 03, 003 159 66 03, 003 159 67 03, 003 159 68 03, 003 159 71 03, 003 159 81 03, 003 159 94 03, 003 159 97 03, 004 159 07 03, 004 159 19 03, 09482-00549, 0K23A-18-110, 101 000 044 AA...VIEW MORE
Additional Fitment Information:
| Vehicle |
|---|
| 2003 - Mitsubishi Lancer |
- NGK G-Power Platinum Spark Plug
- Gap 0.044"
- G-Power Spark Plug
- Product Attributes:
- Seat Type: Flat
- Electrical Terminal Type: Non-removable Nut
- Center Electrode Core Material: Copper
- Part Number: Bkr5egp
- Hex Size: 5/8
- Reach: .75
- Center Electrode Tip Material: Platinum
- Stock Number: 7090
- Ground Electrode Tip Design: Trapezoid
- Manufacturer Heat Range: 5
- Ground Configuration: Standard
- Pre-Gap Size: .040
- Resistance: 5000
- Insulator Height: 50.50
- Ground Electrode Core Material: Nickel
- NGK Spark Plugs (U.S.A.), Inc. is the largest OE supplier and manufacturer of spark plugs for domestic and import vehicles in North America. Its OE legacy, unsurpassed quality and leading vehicles in operation coverage reinforces NGK as The Ignition Specialist. With over 80 years of automotive expertise NGK has built a reputation for quality and reliability; manufacturing spark plugs for virtually every automotive, motorcycle, marine and small engine application. We are committed to be the premier partner with our customers, while maintaining original equipment standards for the highest durability and operational performance. With state-of-the-art manufacturing, inventory and distribution facilities in North America and across the globe, NGK is dedicated to providing customers with world-class products and services.
-
Suggested Purchase Quantity: 6
- Most jobs typically require 6 of this item.
- This item must be purchased in quantities of 4
This Part Fits the Following OEM/Substitute Numbers:
3034, 3412, 3412-2, 3436, 3436-2, 3980, 41-800, 4202, 4503, 4507, 4701, 6702, 6726, 6730, 696202, 7090, AGSP32FSM, AP3924...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Aspiration | CID |
|---|---|---|---|---|---|
| 2003 - Mitsubishi Lancer | L | 2000 | 4 Cyl 2.0L | Naturally Aspirated | - |
- ANCO Conventional 31 Series Wiper Blades 18
- Original Blade Type
- ANCO 31-Series Wiper Blade (Pack of 1)
- 31-Series
- Product Attributes:
- Adapters Required: No
- Pressure Point Quantity: 6
- Adapters Included: Yes
- Frame Color: Black
- Wiper Blade Connection Type: J-hook: 9x3mm; Classic Side-pin: 3/16"; Classic Bayonet: 7mm
- Blade Material: Duraklear - Natural Rubber
- Frame Material: Metal; Plastic
- Blade Type: Conventional/bridge
- Refillable: Yes
- The 31-Series KwikConnect wiper blade boasts reliable wiper performance.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
1385688, 15595485, 18-1, 18-10, 18-2, 18-51, 18-510, 18-52, 18-53, 18-58, 18-8, 22110158, 2580418, 2580419, 2771913, 2771914, 2889960, 33-183...VIEW MORE
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2003 - Mitsubishi Lancer | Front Right |
- NGK V-Power Spark Plug
- Gap 0.044" Actual OE Manufacturer 30,000 mi OE Mfr Recommended Service Interval
- V-Power Spark Plug
- Product Attributes:
- Seat Type: Flat
- Electrical Terminal Type: Non-removable Nut
- Center Electrode Core Material: Copper
- Part Number: Bkr5e-11
- Hex Size: 5/8
- Reach: .75
- Center Electrode Tip Material: Nickel
- Stock Number: 6953
- Ground Electrode Tip Design: Standard
- Manufacturer Heat Range: 5
- Ground Configuration: Standard
- Pre-Gap Size: .044
- Resistance: 5000
- Insulator Height: 50.50
- Ground Electrode Core Material: Nickel
- NGK Spark Plugs (U.S.A.), Inc. is the largest OE supplier and manufacturer of spark plugs for domestic and import vehicles in North America. Its OE legacy, unsurpassed quality and leading vehicles in operation coverage reinforces NGK as The Ignition Specialist. With over 80 years of automotive expertise NGK has built a reputation for quality and reliability; manufacturing spark plugs for virtually every automotive, motorcycle, marine and small engine application. We are committed to be the premier partner with our customers, while maintaining original equipment standards for the highest durability and operational performance. With state-of-the-art manufacturing, inventory and distribution facilities in North America and across the globe, NGK is dedicated to providing customers with world-class products and services.
-
Suggested Purchase Quantity: 6
- Most jobs typically require 6 of this item.
- This item must be purchased in quantities of 4
This Part Fits the Following OEM/Substitute Numbers:
0000-18-BP01, 09482-00566, 12599-6771-6, 1765234, 1835270T, 1844168T, 1Y09, 21025103, 22401 55Y15, 22401-50Y05, 2240155Y75, 22401KA210, 2430, 2FR3LS6, 3130, 3924, 4002, 41-627...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Aspiration | CID |
|---|---|---|---|---|---|
| 2003 - Mitsubishi Lancer | L | 2000 | 4 Cyl 2.0L | Naturally Aspirated | - |
- ANCO Conventional 31 Series Wiper Blades 24
- Original Blade Type
- ANCO 31-Series Wiper Blade (Pack of 1)
- 31-Series
- Product Attributes:
- Adapters Required: No
- Adapters Included: Yes
- Frame Color: Black
- Wiper Blade Connection Type: J-hook: 9x3mm, 9x4mm; Classic Side-pin: 1/4"
- Blade Material: Duraklear - Natural Rubber
- Frame Material: Metal; Plastic
- Blade Type: Conventional/bridge
- Refillable: Yes
- The 31-Series KwikConnect wiper blade boasts reliable wiper performance.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
22086281, 24-1, 24-4, 24-51, 24-54, 24-59, 24-9, 30-240, 350-240, 3724, 39-240, 40324, 40724, 4724, 500-24, 60-024-1, 60-024-4, 60-024-9...VIEW MORE
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2003 - Mitsubishi Lancer | Front Left |
- Spark Plug Iridium Power
- Gap 0.044 Iridium Power - Performance Upgrade with World's Smallest Center Electrode (0.4 mm Dia.) & Tapered Tip Patented U-Groove Design & Patented Ir Alloy (90% Ir)
- Spark Plug Iridium Power
- Iridium Power
- Product Attributes:
- Hex Size: 16.0
- Reach: 19.00
- Center Electrode Tip Material: Iridium
- Seat Type: Flat
- Ground Electrode Tip Design: Tapercut, U-groove
- Center Electrode Core Material: Copper
- Ground Configuration: Standard
- Pre-Gap Size: 1.1
- Resistance: 5000
- Ground Electrode Core Material: Nickel
- Increased performance with World's smallest Iridium Center Eletrode (0.4mm).
-
Suggested Purchase Quantity: 8
- Most jobs typically require 8 of this item.
- This item must be purchased in quantities of 4
This Part Fits the Following OEM/Substitute Numbers:
0000-18-BP01, 0000-18-JE41, 003 159 31 03, 003 159 54 03, 003 159 66 03, 003 159 67 03, 003 159 68 03, 003 159 71 03, 003 159 81 03, 003 159 94 03, 004 159 07 03, 004 159 19 03, 09482-00549, 0K23A-18-110, 101 000 044 AA, 101 905 611 A, 101 905 631 A, 101 905 631 F...VIEW MORE
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 2003 - Mitsubishi Lancer | ES |
- 18" TRICO Exact Fit Wiper Blade
- 9mm Hook, 3/16" Side Lock, 7mm Bayonet
- TRICO Exact Fit
- Provides original factory quality for vehicles with metal conventional wipers
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2003 - Mitsubishi Lancer | Right |
- NGK Standard Spark Plug
- Gap 0.044"
- Standard Spark Plug
- Product Attributes:
- Seat Type: Flat
- Electrical Terminal Type: Non-removable Nut
- Center Electrode Core Material: Copper
- Part Number: Bkr5es-11
- Hex Size: 5/8
- Reach: .75
- Center Electrode Tip Material: Nickel
- Stock Number: 2382
- Ground Electrode Tip Design: Standard
- Manufacturer Heat Range: 5
- Ground Configuration: Standard
- Pre-Gap Size: .044
- Resistance: 5000
- Insulator Height: 50.50
- Ground Electrode Core Material: Nickel
- NGK Spark Plugs (U.S.A.), Inc. is the largest OE supplier and manufacturer of spark plugs for domestic and import vehicles in North America. Its OE legacy, unsurpassed quality and leading vehicles in operation coverage reinforces NGK as The Ignition Specialist. With over 80 years of automotive expertise NGK has built a reputation for quality and reliability; manufacturing spark plugs for virtually every automotive, motorcycle, marine and small engine application. We are committed to be the premier partner with our customers, while maintaining original equipment standards for the highest durability and operational performance. With state-of-the-art manufacturing, inventory and distribution facilities in North America and across the globe, NGK is dedicated to providing customers with world-class products and services.
-
Suggested Purchase Quantity: 6
- Most jobs typically require 6 of this item.
- This item must be purchased in quantities of 4
This Part Fits the Following OEM/Substitute Numbers:
04887031, 1765269, 18814-11051, 22401-85E15, 22401-85E75, 2382, 3926, 3926BP, 3926DP2, 3927, 4887031, 5-86121749, 5-86121749-0, K5RTC-11, K5RTC11, K5TC
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Aspiration | CID |
|---|---|---|---|---|---|
| 2003 - Mitsubishi Lancer | L | 2000 | 4 Cyl 2.0L | Naturally Aspirated | - |
- Product Attributes:
- Cross Section: K-section
- Top Width: .54
- Rib Profile: Straight Rib
- Outside Circumference:
- 31.17
- 791.72
- Rib Depth: Deep
- Standards: Sae J1459, Sae J2432
- Effective Length:
- 30.51
- 774.96
- Minimum Operating Temperature:
- -42.7
- -45
- 381: 4
- Maximum Operating Temperature:
- 100
- 212
This Part Fits the Following OEM/Substitute Numbers:
11720-26E02, 11720-26E12, 11950 31U01, 11950-31000, 11950-31U00, 11950-31U02, 11950-8J100, 11950-8J110, 146-040770, 146-040775, 146-040780, 25-040305, 25-74030, 305K4, 31110-P01-003, 31110-P01-0031, 31110-P01-004, 31110-P01-0041...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2003 - Mitsubishi Lancer | L | 2000 | Alternator | 4 Cyl 2.0L | - |
- Front Floor Mats
- Black; 2 piece
- HD FRONT FLOOR MATS
- Heavy Duty Floor Mat
- Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov.
- Style: Molded
-
Features:
- Guaranteed Not To Crack Or Break
- 0.3750 in. High Ridges
- Up To 40 percent Taller Ridges
- Extra Thick Driver Heal Pad
- Nibs On Back-Prevent Slippage
- Easily Cleaned
- Made In USA
- Year Round Protection
- Available for virtually all of today's top selling vehicles, Husky Liners Heavy Duty Floor Mats are made ultra tough to take whatever abuse you throw at them. Other mats have met their match.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2003 - Mitsubishi Lancer | Front |
Showing 1 - 10 of 1012 products
Loading...