2019 Subaru Impreza Lexus Parts
Choose your Part Name for your 2019 Subaru Impreza
A/C Condenser
Accessory Drive Belt
Air / Fuel Ratio Sensor
Air Bag Clockspring
Air Cleaner Assembly
Air Filter
Air Intake Kit
Alignment Camber Kit
Automatic Transmission Drain Plug Seal
Automatic Transmission Filter O-Ring
Automatic Transmission Oil Cooler
Automatic Transmission Seal
Back Up Light Bulb
Brake Backing Plate
Brake Fluid
Brake Master Cylinder
Cabin Air Filter
Cargo Area Liner
Cargo Carrier
Cargo Holder
Catalytic Converter Gasket
Direct Ignition Coil
Disc Brake Kit
Disc Brake Pad Set
Disc Brake Rotor
Engine Camshaft Position Sensor
Engine Coolant / Antifreeze
Engine Coolant Hose
Engine Coolant Reservoir Cap
Engine Coolant Thermostat
Engine Coolant Thermostat Gasket
Engine Crankshaft O-Ring
Engine Crankshaft Position Sensor
Engine Crankshaft Seal
Engine Mount
Engine Oil Cooler Seal
Engine Oil Drain Plug
Engine Oil Drain Plug Gasket
Engine Oil Filter
Engine Oil Level Sensor
Engine Oil Level Sensor Gasket
Engine Oil Level Sensor O-Ring
Engine Oil Pan
Engine Oil Pan Gasket
Engine Oil Pan O-Ring
Engine Oil Pressure Switch
Engine Oil Pump Pickup Tube Gasket
Engine Oil Pump Pickup Tube O-Ring
Engine Timing Chain
Engine Timing Chain Tensioner
Engine Torque Damper
Engine Valve Cover
Engine Valve Cover Gasket
Engine Valve Cover O-Ring
Engine Valve Cover Washer Seal
Engine Variable Valve Timing (VVT) Oil Control Valve
Engine Variable Valve Timing (VVT) Solenoid
Engine Water Pump
Exhaust Manifold Gasket Set
Exhaust Muffler Gasket
Exhaust Pipe Flange Gasket
Exhaust Pipe to Manifold Gasket
Flood Light
Floor Mat Set
Fog Light
Fog Light Bulb
HVAC Blower Motor
HVAC Heater Hose
Headlight Bulb
Headlight Wiring Harness
Hood Light Pod
Ignition Knock (Detonation) Sensor
License Plate Light Bulb
Liftgate Latch
Light Bar
Manual Transmission Mount
Manual Transmission Shift Shaft Coupling
Mass Air Flow Sensor
Multi-Purpose Light Bulb
Multi-Purpose O-Ring
Neutral Safety Switch
Oxygen Sensor
PCV Valve Connector
Parking Light Bulb
Radiator
Radiator Cap
Radiator Coolant Hose
Roof Rack Mount Kit
Seat Cover
Seat Cushion Cover
Side Marker Light Bulb
Spark Plug
Starter Motor
Steering Tie Rod End
Sunroof Deflector
Suspension Ball Joint
Suspension Control Arm
Suspension Control Arm Bushing
Suspension Stabilizer Bar Link
Suspension Strut Bearing
Tail Light Bulb
Telematics Input Controller
Tent
Tire Pressure Monitoring System Programmable Sensor
Tire Pressure Monitoring System Programmable Sensor Service Kit
Tire Pressure Monitoring System Sensor Service Kit
Trailer Connector Kit
Trailer Hitch
Transmission Drain Plug
Transmission Filter Gasket
Transmission Oil Filter
Transmission Oil Pan
Transmission Oil Pan Gasket
Trunk or Cargo Area Light
Turn Signal Light Bulb
Vehicle-Mounted Spotlight
Wheel Adapter
Wheel Bearing and Hub Assembly
Wheel Lug Nut
Windshield Wiper Blade
Image
Product
Price
- 12" TRICO Exact Fit Wiper Blade (Rear)
- Roc Lock 3
- TRICO Exact Fit
- Provides critical rear visibility in today's aggressive driving environment
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2019 - Subaru Impreza | Rear |
- ; Aluminium Valve Aluminum valve Replaces EZ-sensor rubber valve TPMS service kit for EZ-sensor Torque: 62in-lbs , 7N.m
- Programmable TPMS EZ-Sensor Service Pack
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
Additional Fitment Information:
| Vehicle |
|---|
| 2019 - Subaru Impreza |
- Radiator cap
- Relief pressure 16 lb
- Standard
- Product Attributes:
- Cap Depth: 0.97
- Lever Type:
- No
- Standard
- Coolant Recovery System: Open & Closed System
- Quick Pressure Release: No
- Manufactured to meet all OEM specifications. Designed to be easy to install and remove. Manufactured from high quality components with proper relief and vacuum valves. Quality tested to stand up to even the most demanding automotive cooling systems.
This Part Fits the Following OEM/Substitute Numbers:
10233, 10233ST, 12R8, 1350A730, 1640162090, 1678-29300, 17167, 1793282Z00, 214301P111, 253301P000, 253303K000, 253303Z000, 253304H000, 4495805, 45137AE003, 45137AE00B, 45137AE01A, 7516...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2019 - Subaru Impreza | H | 1995 | 4 Cyl 2.0L | - |
- 2nd Gen Crosstrek / 5th Gen Impreza High-Performance All-Aluminum Radiator
- CSF manufactures the most advanced and efficient radiator in the industry for your Crosstrek/Impreza. CSF uses innovative tube and fin technologies with industry-leading testing methods to maximize airflow and heat dissipation.
- Product Attributes:
- Core Material: Aluminum
- Title: 2nd Gen Crosstrek / 5th Gen Impreza High-performance All-aluminum Radiator
-
Features:
- 2-Row - 42mm Ultra-High-Performance Core
- Cooling Tubes with CSF's Exclusive B-Tube Technology
- 6.5mm Tall Ultra Efficient Fins with a Multi-Louvered Design for Maximum Surface Area Contact
- CNC Machined Mounting Brackets and OEM Style Inlet/Outlet
- 100% All Aluminum TIG-Welded Construction
- Smooth Satin Finish
- True Plug-and-Play "Drop-in Fit" Installation Requires Absolutely No Modifications
- Individually Leak and Pressure Tested
- 2-Year Limited Warranty
- The 42mm 2-Row aluminum core not only increases the fluid capacity of the radiator, but also improves the cores ability to dissipate heat. CSF's Exclusive B-Tube Technology improves heat transfer by approximately 15% over regular oval welded tubes. In addition, the super-efficient multi-louvered fins maximize airflow through the core for the best possible performance. Efficiency is key in off-roading as speeds tend to be lower overall so you end up relying on the fans to move most of the air over the radiator. While the factory fans do a decent job pulling air through the radiator core, it is still less airflow than you'd typically see in city driving. A larger and more efficient core will keep your engine temps in check and keep your engine running strong. Also, a larger core also helps when your radiator is covered in dust, dirt, or mud. While a radiator isn't functioning at peak efficiency in there situations, the more overall cooling capacity you have the better. In Addition, the end tanks are made from high grade aluminum and TIG welded to the core for extra strength. In contrast, the OEM crimped onto plastic end tank design is much weaker and creates a weak point where failure is more likely. Because the CSF radiator is designed as a true plug-and-play drop-in fit application, installation requires absolutely no modifications, trimming, or cutting.
This Part Fits the Following OEM/Substitute Numbers:
45111FL001, 45111FL00B
Additional Fitment Information:
| Vehicle | Block | CC | Engine Designation | Region | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|---|
| 2019 - Subaru Impreza | H | 1995 | FB20 | Canada | 4 Cyl 2.0L | Sport-tech | - |
- Class 1 Trailer Hitch; 1-1/4in. Receiver; Select Subaru Impreza
- 2000lbs. Gross Trailer Weight; 200lbs. Tongue Weight Square Main Body~No Drilling Required~Visibility: Exposed~For Models w/Single Exhaust~Install Time 30 Minutes~Hole Enlargement Required
- CURT 11465 Class 1 Trailer Hitch; 1-1/4-Inch Receiver; Fits Select Subaru Impreza
- Class I 1.25 in. Receiver Hitch
- Product Attributes:
- Gross Trailer Weight: 3500 Lbs.
- Visibility: Exposed
- Weight Carrying Capacity: 2000
- Body Shape: Square
- WARNING CA Proposition 65: No
- Drilling Required: No
- Install Time: 30 Minutes
- WC Tongue Weight: 200
- Receiver Tube Size: 1.250 In.
-
Features:
- Made w/A Vehicle-Specific Design For A Custom Fit
- Tested For Safety In Accordance w/SAE J684
- Precisely Welded For Superior Strength And Fit
- Protected By A Durable High-Gloss Black Powder Coat Finish
- Co-Cured In A Rust-Resistant Liquid Bonderite Coating
- Strengthened w/A Forged Welded Seamless Collar
- Equipped w/An Open-Back Receiver For Easy Cleaning
- Backed By A Limited Lifetime Warranty
- Made in USA [may include imported hardware]
- However you define adventure -- whether its climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the Subaru Impreza (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4 in. receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid Bonderite, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Body | CID |
|---|---|---|---|---|---|---|
| 2019 - Subaru Impreza | H | 1995 | Rear | 4 Cyl 2.0L | Hatchback | - |
- 194;Amber;Super Bright;360degree diffused lens
- W/ LED HEADLAMPS
- Want a bright LED bulb offering improved style and visibility at a great price? Eco Series produces 600 lumens light output. The compact size makes it fit into every application
- Product Attributes:
- Light Output: 600 Lumen
- IP Rating: Ip67
- Prop 65 - Short Label: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Amp Draw per Bulb: 0.65 Amps @ 12v Dc
- Color Temperature: 6,500 Kelvin
- Operating Voltage: 9-16 Dc Voltage
- Prop 65 (C, R or CR): Cr
-
Features:
- LED Source: up to 23 x 3020 LEDs
- Up to 600LM total output per bulb (high mode)
- Color: White/Amber/Red
- Current draw: 0.65A @ 12V (high mode)
- Voltage: 9V - 18V DC
- Diffused 360 degree lens creates smooth all-around illumination
- Compact size similar to stock bulb to ensure there are no fitment or clearance issues
- Polarity reversible contact points
- ECO Series LED bulbs offer improved style and visibility at a great price. The size is similar to the OEM bulb so converting to LED bulbs is as easy as changing the stock bulb. The smooth 360degree diffused lens illumination brightens the darkest spaces and make your vehicle stand out.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2019 - Subaru Impreza | Rear |
- Camber Adjusting Kit
- From Minus 1-3/4 to Plus 1-3/4 Degrees of Change Single Offset Adjuster with 14 (mm) Bolts
- MOOG K90474 Camber Adjusting Kit
-
Features:
- Can bring vehicles back to factory specification
- Can solve excessive tire wear and steering issues
- Shims and bushings provide precise camber, caster and toe adjustments
- Incorporates proven design and engineering features
- Cam bolts and adjustable ball joints provide alignment for non-adjustable vehicles
- By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry's Problem Solver.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
13322A, 264-3642, 41214, 45K18036, 616-1030, 616-1036, 787504, AA3642, AK90399, K90474, MS50202, MS60005, VV13322A
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2019 - Subaru Impreza | Front |
- Exhaust Manifold Gasket Set
- FEL-PRO MS 95088 Exhaust Manifold Gasket Set
- Fel-Pro® gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
This Part Fits the Following OEM/Substitute Numbers:
0378019, 0951334, 14038-AA000, 18616, MS12392
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2019 - Subaru Impreza | H | 1995 | 4 Cyl 2.0L | - |
- Custom Wiring Harness; 4-Way Flat Output; Select Subaru Impreza
- Circuit Protected And Powered; 3-Wire System; 4 Way Flat; Tail Light Circuit 6.0 Amps; Turn And Brake Circuits 3.0 Amps Install Time 45 Minutes
- CURT 56367 Vehicle-Side Custom 4-Pin Trailer Wiring Harness; Fits Select Subaru Impreza
- Custom Wiring Harness
- Product Attributes:
- Output Type: 4-way Flat
- Electrical System Type: 3w
- Converter Type: Circuit Protected Powered
- WARNING CA Proposition 65: Yes
- Install Time: 45 Minutes
- Turn and Brake Circuits: 3.0 Amp
- Tail Light Circuits: 6.0 Amp
-
Features:
- Plugs Into Vehicle Tail Light To Provide A 4-Way Flat Socket
- Simple Plug-And-Play Design Eliminates Cutting Or Splicing
- 4-Way Flat Output Connects Tail Lights Brake Lights Turn Signals
- Equipped With A Powered 3-Wire To 2-Wire Tail Light Converter
- Constructed w/Smt Circuitry For Better Performance And Durability
- Dust Cover Included To Keep Connector Clean When Not In Use
- Backed By A Limited One-Year Warranty
- Made In USA
- If your vehicle is not equipped with wiring for towing a trailer, CURT custom wiring is the ideal solution. A custom wiring harness -- also called a T-connector -- is a simple, plug-and-play electrical device that plugs into your automotive electric system and provides a standard, universal trailer wiring connection. This is done using two or more vehicle-specific, OEM-compatible connectors to plug into the taillight assembly, eliminating the need for cutting, splicing and soldering during installation. Custom wiring harnesses are made vehicle-specific, and while they are not available for all vehicles, they do offer one of the fastest, easiest and most secure ways to wire a vehicle for towing. This particular plug-in harness provides a 4-way flat connector socket and is designed to be a custom wiring harness to fit certain years of the Subaru Impreza (to verify your vehicle compatibility, see application info). It comes with all necessary wiring components to establish a reliable trailer wiring connection, as well as a dust cover to keep the connector clean when not in use. You have a picture in mind of your next destination -- maybe its the boat landing at your favorite fishing spot, maybe its a campsite that overlooks one of natures masterpieces, or maybe its the next big jobsite. However, turning that picture into a reality takes more than just daydreaming. It takes a solid connection and the right amount of power. CURT custom wiring is made with some of the most sophisticated technology in the industry and is designed to install with ease, giving you a long-lasting electrical connection for your towing hitch setup.
Additional Fitment Information:
| Vehicle | Sub Model | Body |
|---|---|---|
| 2019 - Subaru Impreza | Premium | Hatchback |
- Class 1 Trailer Hitch; 1-1/4in. Receiver; Select Subaru Impreza
- 2000lbs. Gross Trailer Weight; 200lbs. Tongue Weight Round Main Body~No Drilling Required~Visibility: Exposed~Install Time 35 Minutes~Hole Enlargement Required~Temporarily Lower Exhaust For Installation~Temporarily Remove Heat Shield For Installation~Temporarily Remove Underbody Panel For Installation
- CURT 11466 Class 1 Trailer Hitch; 1-1/4-Inch Receiver; Fits Select Subaru Impreza
- Class I 1.25 in. Receiver Hitch
- Product Attributes:
- Gross Trailer Weight: 2000 Lbs.
- Visibility: Exposed
- Weight Carrying Capacity: 2000
- Body Shape: Round
- WARNING CA Proposition 65: No
- Drilling Required: No
- Install Time: 35 Minutes
- WC Tongue Weight: 200
- Receiver Tube Size: 1.250 In.
-
Features:
- Made With A Vehicle-Specific Design For A Custom Fit
- Tested For Safety In Accordance With Sea J684
- Precisely Welded For Superior Strength And Fit
- Protected By A Durable High-Gloss Black Powder Coat Finish
- Co-Cured In A Rust-Resistant Liquid Bonderite Coating
- Strengthened With A Cast
- Welded
- Seamless Collar
- Equipped With An Open-Back Receiver For Easy Cleaning
- Backed By A Limited Lifetime Warranty
- Made in USA [may include imported hardware]
- However you define adventure -- whether its climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the Subaru Impreza (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4 in. receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid Bonderite, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Body | CID |
|---|---|---|---|---|---|---|
| 2019 - Subaru Impreza | H | 1995 | Rear | 4 Cyl 2.0L | Sedan | - |
Showing 1 - 10 of 491 products
Loading...