2020 BMW M240i Lexus Parts
Choose your Part Name for your 2020 BMW M240i
A/C Condenser
A/C Evaporator Core
A/C Evaporator Temperature Sensor
A/C Expansion Valve
A/C Line O-Ring
A/C Refrigerant Pressure Sensor
ABS Modulator Insulator
ABS Wheel Speed Sensor
Accessory Drive Belt
Accessory Drive Belt Tensioner Assembly
Air Filter
Ambient Air Temperature Sensor
Axle Hub Mounting Bolt
Axle Nut
Back Up Light Bulb
Back Up Light Switch
Brake Hydraulic Hose
Brake Light Switch
Brake Master Cylinder
Brake Master Cylinder Nut
Bumper Cover Retainer
CV Joint Nut
Cabin Air Filter
Cargo Area Liner
Cargo Carrier
Clutch Flywheel Bolt
Clutch Pilot Bearing
Clutch Release Arm
Clutch Release Arm Bushing
Clutch Release Bearing Clip
Clutch Slave Cylinder
Clutch Starter Safety Switch
Courtesy Light Bulb
Differential Pinion Seal
Direct Ignition Coil
Direct Injection High Pressure Fuel Pump
Disc Brake Kit
Disc Brake Pad Set
Disc Brake Pad Wear Sensor
Disc Brake Rotor
Disc Brake Rotor Set Screw
Door Interior Trim Panel Retainer
Door Latch Assembly
Door Lock Actuator Motor
Drive Shaft Damper
Emission Check Valve
Engine Auxiliary Water Pump
Engine Camshaft Follower
Engine Camshaft Position Sensor
Engine Coolant / Antifreeze
Engine Coolant Reservoir
Engine Coolant Reservoir Hose
Engine Coolant Temperature Sensor
Engine Coolant Thermostat / Water Outlet Assembly
Engine Coolant Thermostat Kit
Engine Cooling Fan Assembly
Engine Crankshaft Position Sensor
Engine Crankshaft Seal
Engine Cylinder Head Gasket
Engine Intake Manifold Gasket
Engine Intake Manifold Gasket Set
Engine Intake Manifold Seal
Engine Mount
Engine Oil Cooler Gasket
Engine Oil Drain Plug
Engine Oil Drain Plug Gasket
Engine Oil Filler Cap
Engine Oil Filter
Engine Oil Filter Adapter Gasket
Engine Oil Filter Housing
Engine Oil Filter Housing Gasket
Engine Oil Filter Kit
Engine Oil Level Sensor
Engine Oil Level Sensor O-Ring
Engine Oil Pressure Switch
Engine Timing Camshaft Sprocket
Engine Timing Chain
Engine Valve Cover
Engine Valve Cover Gasket
Engine Valve Spring Retainer Keeper
Engine Valve Stem Oil Seal
Engine Variable Valve Timing (VVT) Solenoid
Engine Variable Valve Timing (VVT) Sprocket
Engine Water Pump
Engine Water Pump Gasket
Evaporative Emissions System Leak Detection Pump Seal
Exhaust Clamp
Exhaust Manifold Gasket
Exhaust System Hanger
Exhaust System Kit
Floor Mat Set
Fog Light Screw
Fuel Injection Air Flow Meter
Fuel Injection Pressure Sensor
Fuel Injection Throttle Body Mounting Gasket
Fuel Injector
Fuel Injector O-Ring
Fuel Pump Gasket
Fuel Tank Cap
HVAC Air Adjustment Control Motor
HVAC Blower Motor
HVAC Blower Motor Control Module
HVAC Blower Motor Regulator
HVAC Evaporator Temperature Switch
HVAC Heater Core
HVAC Pressure Switch
Headlight Level Sensor
Headlight Washer Pump
High Intensity Discharge (HID) Lighting Ballast
Hood Lift Support
Hood Safety Catch
Ignition Knock (Detonation) Sensor
Lateral Arm
Lateral Arm Nut
License Plate Bracket
Manual Transmission Mount
Mass Air Flow Sensor
Multi-Purpose Light Bulb
Oxygen Sensor
Parking Aid Sensor
Parking Brake Adjuster
Parking Brake Hardware Kit
Parking Brake Lever
Parking Brake Shoe
Parking Light Bulb
Rack and Pinion Bellows
Radiator
Seat Cover
Seat Cushion Cover
Spark Plug
Spark Plug Tube Seal
Steering Tie Rod Assembly
Steering Tie Rod End
Suspension Control Arm
Suspension Control Arm Bolt
Suspension Control Arm Bushing
Suspension Control Arm Link
Suspension Control Arm Nut
Suspension Crossmember Insulator
Suspension Knuckle Bushing
Suspension Shock Absorber Bellows
Suspension Shock Absorber Mount
Suspension Stabilizer Bar Link Kit
Suspension Strut Bellows
Suspension Strut Mount
Suspension Strut Nut
Suspension Subframe Mount
Suspension Trailing Arm
Suspension Trailing Arm Nut
Tire Pressure Monitoring System (TPMS) Sensor
Tire Pressure Monitoring System (TPMS) Sensor Valve Assembly
Tire Valve Stem Cap
Trailer Hitch
Transmission Clutch Kit
Transmission Oil Pan Kit
Turbocharger Gasket
Turbocharger Oil Line Gasket
Vapor Canister Purge Valve
Wheel Bearing
Wheel Bearing Snap Ring
Wheel Bearing and Hub Assembly
Wheel Hub
Wheel Lug Bolt
Window Shade
Windshield Washer Pump
Windshield Washer Pump Grommet
Windshield Wiper Blade
Windshield Wiper Blade Set
Image
Product
Price
- 22" TRICO Tech Beam Blade
- 9mm Hook, 9x4 Hook, 1/4" Side Lock, Side Pin (17mm), Pinch Tab, Pinch Tab Button, Push Button (22mm), Push Button (19mm)
- TRICO Tech
- All-weather durability
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2020 - BMW M240i | Left |
- 18" TRICO Tech Beam Blade
- 9mm Hook, 9x4 Hook, 3/16" Side Lock, 7mm Bayonet, Side Pin (17mm), Pinch Tab, Push Button (22mm), Push Button (19mm)
- TRICO Tech
- All-weather durability
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2020 - BMW M240i | Right |
- 22" TRICO NeoForm Beam Blade
- Pinch Tab, Push Button (22mm)
- TRICO NeoForm
- Exclusive dual-point coupler helps eliminate streaking
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2020 - BMW M240i | Left |
- PEAK OET European Extended Life Blue 50/50 Pre-diluted; 1 Gallon
- This item must be purchased in quantities of 6
Additional Fitment Information:
| Vehicle |
|---|
| 2020 - BMW M240i |
- Prestone All Vehicles - 10yr/300k mi- Antifreeze+Coolant (1 Gal - Concentrate)
- Extended Life, Full Strength Concentrate
- Product Attributes:
- Biodegradable: No
- California Proposition 65: Warning: Reproductive Harm - Www.p65warnings.ca.gov
- Freezing Point: -34
- Recommended Dilution Ratio: 5 To 7
- Phosphate Free: Yes
- Ethylene Glycol: Yes
- Boiling Point at 50 50 Mixture: 229
- Prestone All Vehicles antifreeze+coolant - Concentrate is our optimized formula for All Vehicles; makes, models, years & fluid colors. Our Patented Cor-Guard® Technology (our best coolant innovation in decades) works with all new engines, and also is backward compatible - providing instant protection in older engines. Not only does Prestone Coolant Technology manage engine temperature all year round and protects against freezing, it also uniquely protects the engine from serious damage. No matter what type of coolant is currently in your engine, a Single Top-off of Patented Cor-Guard® Technology instantly protects parts better from corrosion, buildup, pitting, scaling, rust and other damage; a complete replacement of all coolant protects to the maximum. Internal engine damage can cause parts failure, resulting in expensive auto repair shop bills and downtime inconveniences. Using Prestone Antifreeze+Coolant protects against engine issues and those inconveniences. This patented fluid is designed to last 10yrs / 300,000 miles and will protect the internal parts of the engine for 10yrs / 300,000 miles
- This item must be purchased in quantities of 6
Additional Fitment Information:
| Vehicle |
|---|
| 2020 - BMW M240i |
- Prestone Amam Gen 2 50/50 6/1 GAL
- Extended Life 50/50, Ready to Use Prediluted
- Product Attributes:
- California Proposition 65: Warning: Reproductive Harm - Www.p65warnings.ca.gov
- Freezing Point: -34
- Recommended Dilution Ratio: No Dilution Required
- Phosphate Free: Yes
- Boiling Point at 50 50 Mixture: 229
- for corrosion protection for cars and light duty trucks. Top-off a vehicle’s cooling system with Prestone 50/50, which is a blend of concentrated antifreeze/coolant and demineralized water.
- This item must be purchased in quantities of 6
Additional Fitment Information:
| Vehicle |
|---|
| 2020 - BMW M240i |
- Premium Low-Met OE Equivalent Pad
- Product Attributes:
- WVA: 25028
- Nominal Thickness (MM): 18.2
- Suface Finishing: Chamfered & Slotted
- Brake System: Brembo
- Wear Indicator: Prepared For Wear Indicator
- FMSI: 8822-d1609
- Specifically designed for the North American market, this Brembo formulated friction material with premium shim offers comfortable, quiet, smooth braking and cleaner wheels. Designed with the European car owner in mind, Brembo's Low-Met Brake Pads are formulated for superior braking performance in all driving conditions. Brembo's Low-Met formulations are comparable to the OE with all Low-Met pads receiving an ECE-R90 approval.
- They are sold as a set and only quantity 1 is required for both wheels
This Part Fits the Following OEM/Substitute Numbers:
34106799805, 34106859067, 34106878878, 34116850850, 34116859066, 34116878876, D1609 8822
Additional Fitment Information:
| Vehicle | Position | Sub Model |
|---|---|---|
| 2020 - BMW M240i | Front | Base |
- Premium NAO Ceramic OE Equivalent Pad
- Product Attributes:
- WVA: 25028
- Nominal Thickness (MM): 18.2
- Suface Finishing: Chamfered & Slotted
- Brake System: Brembo
- Wear Indicator: Prepared For Wear Indicator
- FMSI: 8822-d1609
- Specifically designed for the North American market, this Brembo formulated friction material with premium shim offers comfortable, quiet, smooth braking and cleaner wheels.
- They are sold as a set and only quantity 1 is required for both wheels
This Part Fits the Following OEM/Substitute Numbers:
34106799805, 34106859067, 34106878878, 34112284969, 34116850850, 34116859066, 34116859282, 34116865460, 3411687876, D1609 8822
Additional Fitment Information:
| Vehicle | Position | Sub Model |
|---|---|---|
| 2020 - BMW M240i | Front | Base |
- Premium Low-Met OE Equivalent Pad
- Product Attributes:
- WVA: 25029
- Nominal Thickness (MM): 16.6
- Suface Finishing: Chamfered
- Brake System: Brembo
- Wear Indicator: Prepared For Wear Indicator
- FMSI: 8885-d1656
- Specifically designed for the North American market, this Brembo formulated friction material with premium shim offers comfortable, quiet, smooth braking and cleaner wheels. Designed with the European car owner in mind, Brembo's Low-Met Brake Pads are formulated for superior braking performance in all driving conditions. Brembo's Low-Met formulations are comparable to the OE with all Low-Met pads receiving an ECE-R90 approval.
- They are sold as a set and only quantity 1 is required for both wheels
This Part Fits the Following OEM/Substitute Numbers:
34212284989, 34216855474, 34216876422, 34216887576, 34218099354, D1656 8885
Additional Fitment Information:
| Vehicle | Position | Sub Model |
|---|---|---|
| 2020 - BMW M240i | Rear | Base |
- Class 1 Trailer Hitch; 1-1/4in. Receiver; Select BMW Vehicles
- 2000lbs. Gross Trailer Weight; 200lbs. Tongue Weight
- CURT 11367 Class 1 Trailer Hitch; 1-1/4-Inch Receiver; Fits Select BMW Vehicles
- Class I 1.25 in. Receiver Hitch
- Product Attributes:
- Gross Trailer Weight: 2000 Lbs.
- Visibility: Concealed
- Weight Carrying Capacity: 2000
- Body Shape: Square
- WARNING CA Proposition 65: No
- Drilling Required: No
- Install Time: 45 Minutes
- WC Tongue Weight: 200
- Receiver Tube Size: 1.250 In.
-
Features:
- Made w/A Vehicle-Specific Design For A Custom Fit
- Tested For Safety In Accordance w/SAE J684
- Precisely Welded For Superior Strength And Fit
- Protected By A Durable High-Gloss Black Powder Coat Finish
- Co-Cured In A Rust-Resistant Liquid Bonderite Coating
- Strengthened w/A Cast Welded Seamless Collar
- Equipped w/An Open-Back Receiver For Easy Cleaning
- Backed By A Limited Lifetime Warranty
- Made in USA [may include imported hardware]
- However you define adventure -- whether its climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the BMW 228i, 320i, 325i, 328d, 328i, 335i xDrive, 340i, 428i and 435i (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4 in. receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid Bonderite, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2020 - BMW M240i | Rear |
Showing 1 - 10 of 448 products
Loading...