2010 Ford Explorer Suspension Parts
Choose your Part Name for your 2010 Ford Explorer
Air Suspension Compressor Kit
Air Suspension Helper Spring
Coil Spring Insulator
Lateral Arm
Suspension Ball Joint
Suspension Control Arm
Suspension Control Arm Bushing
Suspension Control Arm and Ball Joint Assembly
Suspension Knuckle Bushing
Suspension Leveling Kit
Suspension Stabilizer Bar Bushing
Suspension Stabilizer Bar Bushing Kit
Suspension Stabilizer Bar Link Kit
Suspension Stabilizer Bar Link Nut
Suspension Strut
Suspension Strut Bellows
Suspension Strut Hardware Kit
Suspension Strut and Coil Spring Assembly
Suspension Trailing Arm
Image
Product
Price
- Ball Joint
- Both New and Original Designs can be Installed on Vehicle
- MOOG K80771 Ball Joint
- Product Attributes:
- Cotter Pin Hole: Yes
- Adjustable: No
- Suspension Grade Type: Standard
- Maximum Outside Diameter: 2.500
- Mounting Hole Quantity: 0
- Castle Nut Included: Yes
- Mounting Type: Press-in
- Greaseable: Yes
-
Features:
- PROBLEM SOLVER® GUSHER BEARING -- Metal-to-metal design provides strength and allows grease to flow through bearing surface for reduced friction and long life
- STRONG AND DURABLE -- Ball studs are heat treated to match or exceed OE requirements to inhibit premature failure and improve fatigue strength
- GREASEABLE SOCKET -- Reduces corrosion and wear by allowing new lubricant to flush contaminants
- KEEPS DIRT AND WATER OUT -- Pre-installed dust boot shields socket components from wear-causing contaminants
- ABSORBS IMPACT -- Belleville preload washer helps keep the bearing package tight as bearings wear
- EASY TO INSTALL -- Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- Backed by superior materials and rigorous testing, MOOG® ball joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front Lower |
- Ball Joint
- Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing Surfaces New Pre-Installed Integral Dust Boot Allows For Ease Of Installation Both New and Original Designs can be Installed on Vehicle
- MOOG K80771 Ball Joint
- Product Attributes:
- Cotter Pin Hole: Yes
- Adjustable: No
- Suspension Grade Type: Standard
- Maximum Outside Diameter: 2.500
- Mounting Hole Quantity: 0
- Castle Nut Included: Yes
- Mounting Type: Press-in
- Greaseable: Yes
-
Features:
- PROBLEM SOLVER® GUSHER BEARING -- Metal-to-metal design provides strength and allows grease to flow through bearing surface for reduced friction and long life
- STRONG AND DURABLE -- Ball studs are heat treated to match or exceed OE requirements to inhibit premature failure and improve fatigue strength
- GREASEABLE SOCKET -- Reduces corrosion and wear by allowing new lubricant to flush contaminants
- KEEPS DIRT AND WATER OUT -- Pre-installed dust boot shields socket components from wear-causing contaminants
- ABSORBS IMPACT -- Belleville preload washer helps keep the bearing package tight as bearings wear
- EASY TO INSTALL -- Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- Backed by superior materials and rigorous testing, MOOG® ball joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
104222A, 10480771, 46D2281A, 505-1281, 533-016, 610.65008, 6L5Z3050-AA, 7L2Z3050A, 7L5Z-3050-A, BJ85345, BJ86375, F87Z-3050-BA, FA2180, FA2180EOS, K80771, MK8695T
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front Lower |
- Stabilizer Bar Link Kit
- with Independent Rear Suspension Includes Polyurethane Bushings and Solid Metal Sleeve for Enhanced Performance - Barrel Nut Allows for Easier Installation
- MOOG K700539 Stabilizer Bar Link Kit
- Product Attributes:
- Sleeve Length: 4.560
- End 1 Type: Bolt On
- Bolt Length: 8.500
-
Features:
- EASY TO INSTALL -- Innovative features like molded bushings that hold coated washers in place and easy-thread 1-in. barrel lock nut make it easier to install than traditional sway bar links
- PREMIUM MATERIALS -- Made from premium materials for long-lasting dependability
- RIGHT TECHNOLOGY FOR THE REPAIR -- Featuring problem-solving innovations for long life, MOOG designs the right sway bar link technology for your vehicle
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- Backed by superior materials and rigorous testing, MOOG sway bar links deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
15835052, 265-1277, 265-2050, 2651222, 2653019, 2653304, 2653307, 536-379, 536-442, 536-491, 6L2Z-5K484BA, K80898, SL91055
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Rear |
- Stabilizer Bar Link Kit
- Includes Polyurethane Bushings and Solid Metal Sleeve for Enhanced Performance - Barrel Nut Allows for Easier Installation
- MOOG K700542 Stabilizer Bar Link Kit
- Product Attributes:
- Sleeve Length: 5.670
- End 1 Type: Bolt On
- Bolt Length: 9.500
-
Features:
- EASY TO INSTALL -- Innovative features like molded bushings that hold coated washers in place and easy-thread 1-in. barrel lock nut make it easier to install than traditional sway bar links
- PREMIUM MATERIALS -- Made from premium materials for long-lasting dependability
- RIGHT TECHNOLOGY FOR THE REPAIR -- Featuring problem-solving innovations for long life, MOOG designs the right sway bar link technology for your vehicle
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- Backed by superior materials and rigorous testing, MOOG sway bar links deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
22761221, 2653305, 2653310, 52037712AB, 534-002, 6L5Z5495AA, SK7275
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front |
- Coil Capacity Increase 15-30 Percent; Fill Out Coil SumoSprings Inspection before Ordering; Do Not Exceed GVWR; Inner Wall Height 0.94 in.
- Coil SumoSprings; Coil Capacity Increase 15-30 Percent; Fill Out Coil SumoSprings Inspection before Ordering; Do Not Exceed GVWR; Inner Wall Height 0.94 in.;
- Coil SumoSprings
-
Features:
- Sold as a pair left and right
- Requires no maintenance
- Proudly made in the U.S.A.
- Fit Both Front And Rear Coil Springs
- Coil SumoSprings Simply Slide Between The Turns Of Coil Springs
- Enhance Front Suspension When Fitting Snow Plow/Winch/Bumper
- Enhance Rear Suspension When Adding Tow Hitch
- Reduces Side To Side Body Roll And Front End Dip
- Produced From SumoSprings Closed Cell Microcellular Urethane
- Progressive Spring Rate
- Coil Capacity Increased By 15 To 30 Percent
- Typical Installation Completed In Less Than 30 Minutes
- Never Load Any Vehicle Beyond The Manufacturers GVWR
- Coil SumoSprings(R) improve the load leveling ability of original equipment front and rear coil springs. Manufactured from micro-cellular urethane, the material's progressive spring rate creates a cushion effect, enhancing capacity and ride comfort. They install by simply being slid between the turns of the coil spring.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front |
- Coil Capacity Increase 15-30 Percent; Fill Out Inspection before Ordering; Do Not Exceed GVWR; Inner Wall Height 0.94 in.
- Coil SumoSprings; Coil Capacity Increase 15-30 Percent; Fill Out Coil SumoSprings Inspection before Ordering; Do Not Exceed GVWR; Inner Wall Height 0.94 in.;
- Coil SumoSprings
-
Features:
- Sold as a pair left and right
- Requires no maintenance
- Proudly made in the U.S.A.
- Fit Both Front And Rear Coil Springs
- Coil SumoSprings Simply Slide Between The Turns Of Coil Springs
- Enhance Front Suspension When Fitting Snow Plow/Winch/Bumper
- Enhance Rear Suspension When Adding Tow Hitch
- Reduces Side To Side Body Roll And Front End Dip
- Produced From SumoSprings Closed Cell Microcellular Urethane
- Progressive Spring Rate
- Coil Capacity Increased By 15 To 30 Percent
- Typical Installation Completed In Less Than 30 Minutes
- Never Load Any Vehicle Beyond The Manufacturers GVWR
- Coil SumoSprings(R) improve the load leveling ability of original equipment front and rear coil springs. Manufactured from micro-cellular urethane, the material's progressive spring rate creates a cushion effect, enhancing capacity and ride comfort. They install by simply being slid between the turns of the coil spring.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front |
- Suspension Ball Joint
- Standard Replacement
- Product Attributes:
- Housing Press Fit Diameter: 44.6 Mm
- Mounting Hardware Included: Yes
- Package Contents: 1 Ball Joint; 1 Castle Nut; 1 Cotter Pin; 1 Snap Ring
- Mounting Hole Quantity: 0
- Castle Nut Included: Yes
- Greaseable: No
- Cotter Pin Hole: Yes
- Dust Boot Material: Rubber
- Attachment Type: Taper
- Adjustable: No
- Suspension Grade Type: Standard
- Bolts/Studs Included: No
- Bearing Material: Polymer
- Mounting Type: Press
-
Features:
- Direct replacement - fits and performs like the original equipment on specific vehicles
- Reliable fit - precision-engineered to match the design and dimensions of original components
- Durable construction - manufactured to strict standards using sturdy, safe materials
- Rigorously tested - thorough quality control measures ensure longevity
- This suspension ball joint is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
1015771, 10480771, 1FFA34550, 2L3Z3050AA, 45D2281, 610.65003, FA2180, GK8695T, JBJ1171, K-8695, K500108, MCF2233, MK8695T, SK500108, TC1672
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front Lower |
- Stabilizer Bar Link Kit
- Original Design
- Product Attributes:
- Spacer Included: No
- Mounting Hardware Included: No
- Grade Type: Regular
- Bushing Color: Red
- Length: 10
- End 1 Type: Male Threaded
- Link Material: Steel
- Bushings Included: Yes
- Greaseable: No
- End 2 Type: Hex Head
- Locking Nuts Included: No
- Sleeve Included: No
- Weight: 0.59 Lb
- Bushing Material: Rubber
- Bolt Thread Size: 0.437
- Sleeve Length: 5.5
- Package Contents: 1 Bolt; 1 Nut; 4 Bushings; 4 Washers; 1 Sleeve
- Bushing Inside Diameter: 0.45
- Washers Included: No
- End 1 Attachment Size : 7/16 In
- Bushing Outside Diameter: 1.18
- Threaded End: Yes
- Grease Fittings Included: No
- Pre-Greased: No
- Bolts Included: No
- Dust Boot Included: No
-
Features:
- Direct replacement - fits and performs like the original equipment on specific vehicles
- Reliable fit - precision-engineered to match the design and dimensions of original components
- Durable construction - manufactured to strict standards using sturdy, safe materials
- Rigorously tested - thorough quality control measures ensure longevity
- This suspension stabilizer bar link kit is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
1016770, 1F6034158, 2L2Z5K483A, 45G0022, 606.65019, GK7275, JTS1401, K-7275, K700542, K7275, MCS18155, MK7275, SL227, TD626W
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front |
- Stabilizer Bar Link Kit
- Product Attributes:
- Spacer Included: No
- Mounting Hardware Included: Yes
- Grade Type: Regular
- Bushing Color: Red
- Length: 234.36
- End 1 Type: Male Threaded
- Link Material: Steel
- Bushings Included: Yes
- Greaseable: No
- End 2 Type: Hex Head
- Locking Nuts Included: No
- Sleeve Included: No
- Weight: 0.59 Lb
- Bushing Material: Rubber
- Bolt Thread Size: 14
- Sleeve Length: 22.08
- Package Contents: 1 Bolt; 4 Bushings; 4 Washers; 1 Nut
- Bushing Inside Diameter: 9.4
- Washers Included: No
- End 1 Attachment Size : 3/8 In; 1/2 In; 5/8 In; 3/4 In; 1 In
- Bushing Outside Diameter: 30.45
- Threaded End: No
- Grease Fittings Included: No
- Pre-Greased: No
- Bolts Included: No
- Dust Boot Included: No
-
Features:
- Direct replacement - fits and performs like the original equipment on specific vehicles
- Reliable fit - precision-engineered to match the design and dimensions of original components
- Durable construction - manufactured to strict standards using sturdy, safe materials
- Rigorously tested - thorough quality control measures ensure longevity
- This suspension stabilizer bar link kit is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
2108021, 45G1577, 606.65027, 6L2Z5K484BA, JTS1157, K80898, MEF139, MK80898, SL828
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Rear |
- Stabilizer Bar Bushing Kit
- Includes Split Design For Easier Installation
- MOOG K200520 Stabilizer Bar Bushing Kit
- Product Attributes:
- Includes Dust Boots: No
- Quantity of Bushings: 2
- Bar Diameter (Inch): 1.260
- Height (Inch): 2.130
- Includes Hardware: No
- Inner Diameter (Inch): 1.260
- Base to Centerline (Inch): 2.270
- Length (Inch): 2.270
- Meets/Exceeds OE Manufacturer Specs: Exceeds
- Part Description: Sway Bar Bushing
- Outer Diameter (Inch): 2.130
-
Features:
- PREMIUM MATERIALS -- Made from high-quality natural rubber material for durability and ride performance
- EXTENDED SERVICE LIFE -- Less prone to splitting, discoloring or cracking with age for long life
- HIGHLY PRECISE ENGINEERING -- Optimized for quiet operation and resistance to wear, salt, road grime and oils
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- Backed by superior materials and rigorous testing, MOOG sway bar bushings deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
This Part Fits the Following OEM/Substitute Numbers:
2652838, 45G1750, 535-530, 550-1763, 6L2Z5484AA, 8L2Z5484A, AA8Z5484A, AA8Z5484B, BSK85149, FB200520, HB200520, JBU1320, MS40874
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2010 - Ford Explorer | Front To Frame |
Showing 1 - 10 of 91 products
Loading...