1995 Porsche 911 Transmission Parts
Choose your Part Name for your 1995 Porsche 911
Clutch Flywheel
Clutch Flywheel Bolt
Clutch Flywheel Ring Gear
Clutch Fork Bearing
Clutch Fork Shaft
Clutch Fork Shaft Cover
Clutch Hydraulic Hose
Clutch Master Cylinder
Clutch Pilot Bearing
Clutch Release Arm
Clutch Release Arm Bushing
Clutch Release Bearing
Clutch Release Bearing Bolt
Clutch Release Bearing Guide
Clutch Shaft Bushing Kit
Clutch Shaft Retainer Plate
Clutch Slave Cylinder
Manual Transmission Differential Bearing
Manual Transmission Drive Axle Seal
Manual Transmission Gasket Set
Manual Transmission Input Shaft Bearing
Manual Transmission Input Shaft Seal
Manual Transmission Manual Shaft Bearing
Manual Transmission Output Shaft Seal
Manual Transmission Seal
Manual Transmission Selector Rod
Manual Transmission Shift Bushing
Manual Transmission Shift Shaft Seal
Transmission Clutch Friction Plate
Transmission Clutch Pressure Plate
Transmission Clutch Pressure Plate Bolt
Transmission Drain Plug
Transmission Oil Pan Gasket
Image
Product
Price
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Club Sport Model
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1995 - Porsche 911 | Carrera |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- For vehicles equipped with replacement flywheels
- 10 X 62mm
Additional Fitment Information:
| Vehicle |
|---|
| 1995 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Bearing (32mm O.D.)
Additional Fitment Information:
| Vehicle |
|---|
| 1995 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Clutch Fork "Open Bearing"
Additional Fitment Information:
| Vehicle |
|---|
| 1995 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- (Axle Flange) (50x80x20 Taper Roller)
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1995 - Porsche 911 | Right |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- M8 x 40mm - Pan Head Screw
- M8 x 40mm
Additional Fitment Information:
| Vehicle |
|---|
| 1995 - Porsche 911 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 40 X 60 X 9mm
Additional Fitment Information:
| Vehicle | Position | Sub Model |
|---|---|---|
| 1995 - Porsche 911 | Front | Carrera 4 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 50 X 90 X 21.7 Axle Carrier
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1995 - Porsche 911 | Left |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- End Cover
Additional Fitment Information:
| Vehicle |
|---|
| 1995 - Porsche 911 |
Showing 1 - 10 of 45 products
Loading...