Image
Product
Price
- Cut to fit
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 216
- 8.5
- End 1 Inside Diameter:
- 1.27
- 32
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.27
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
10403194, 20795743, 215013NT0D, 215013TA0A, 21501JA000, 21501JA100, 21501JA800, 22353, 26348X, 62914, 62915, 66303, 66653, 66654, 8986, A91427, B90295, B90747...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2007 - Nissan Altima | V | 3498 | Upper - Radiator To Filler Neck | GAS | 6 Cyl 3.5L | - |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Assembly (with Fill Neck)
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2007 - Nissan Altima | V | 3498 | Upper | 6 Cyl 3.5L | - |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- This hose assembly includes outlet hose from the radiator, the center pipe with bracket, and the inlet hose to the engine.
- Assembly
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2007 - Nissan Altima | V | 3498 | Lower | 6 Cyl 3.5L | - |
Additional Fitment Information:
| Vehicle | Position | Fuel Type |
|---|---|---|
| 2007 - Nissan Altima | Lower | FULL HYBRID EV-GAS (FHEV) |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- The OE Service upper hose assembly includes the engine outlet hose (to filler neck), the filler neck, and the radiator inlet hose (from filler neck to radiator). The Dayco 72405 upper hose is the engine outlet hose ONLY (to filler neck); also order Dayco 71638 radiator inlet hose (from filler neck to radiator; trim hose as needed) and reuse the original filler neck to equal the OE Service hose assembly.
- Assembly (with Fill Neck)
Additional Fitment Information:
| Vehicle | Position | Fuel Type |
|---|---|---|
| 2007 - Nissan Altima | Upper | FULL HYBRID EV-GAS (FHEV) |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- The OE Service upper hose assembly includes the engine outlet hose (to filler neck), the filler neck, and the radiator inlet hose (from filler neck to radiator). The Dayco 72405 upper hose is the engine outlet hose ONLY (to filler neck); also order Dayco 71638 radiator inlet hose (from filler neck to radiator; trim hose as needed) and reuse the original filler neck to equal the OE Service hose assembly.
- Assembly (with Fill Neck)
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2007 - Nissan Altima | L | 2488 | Upper | GAS | 4 Cyl 2.5L | 152 |
Additional Fitment Information:
| Vehicle | Position | Fuel Type |
|---|---|---|
| 2007 - Nissan Altima | Upper | FULL HYBRID EV-GAS (FHEV) |
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2007 - Nissan Altima | L | 2488 | Lower | GAS | 4 Cyl 2.5L | 152 |
- Curved Radiator Hose
- Product Attributes:
- : 1.34
- Trunk Height: 20 1/2
- End 1 Outside Diameter: 1 5/8
- Hose Type: Single I.d. Hose
- End 2 Inside Diameter: 1 11/32
- End 2 Outside Diameter: 1 5/8
- Color: Black
- Contains Heat Shield: N
- End 1 Inside Diameter:
- 1 11/32
- 1.34
- Centerline Length: 20.5
- SAE Specification: Sae J20r4 Class D-1, Sae J1684 Type Ec
- Contains Protective Sleeve: N
- Material: Epdm
This Part Fits the Following OEM/Substitute Numbers:
16083, 21503-3TA0A, 21503-JA000, 23345, 26594X, 66222, E72406
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2007 - Nissan Altima | L | 2488 | Lower | GAS | 4 Cyl 2.5L | 152 |
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length: 572
- End 1 Inside Diameter:
- 1.31
- 33
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.31
- 33
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
16083, 21503JA000, 23345, 26594X, 66222, 66911, 72406, E72406
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2007 - Nissan Altima | L | 2488 | Lower | GAS | 4 Cyl 2.5L | 152 |
Showing 1 - 10 of 14 products
Loading...