Shop By Product Matching "Exhaust"
Image
Product
Price
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 1983 - Mazda RX-7 |
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1983 - Mazda RX-7 | Center |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 1
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 5.5
- Body Height: 3.75
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: Yes
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 94014 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1983 - Mazda RX-7 | R | 1146 | Rear | 2 Cyl 1.1L | - |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required Main and Pre-Converter
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 1
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 6.375
- Body Height: 3.75
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: Yes
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 3
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 93514 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1983 - Mazda RX-7 | R | 1146 | 2 Cyl 1.1L | - |
- Standard Grade Direct-Fit Catalytic Converter
- Magnaflow Standard Grade Direct-Fit Catalytic Converter
- Direct-Fit Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: Yes
- Tube Material: Stainless Steel
- Outlet Gasket Included: Yes
- Grade Type: Regular
- Hangers Included: No
- Heat Shield Attached: No
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Spun
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 0
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
-
Features:
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Keep the check engine light off with MagnaFlow Standard Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 23690. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 1981-1983 Mazda RX-7. Avoid potential exhaust leaks by using the included gaskets to get a proper seal. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1983 - Mazda RX-7 | R | 1146 | Front | 2 Cyl 1.1L | - |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.375
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 53004 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1983 - Mazda RX-7 | R | 1146 | Front | 2 Cyl 1.1L | - |
- Standard Grade Direct-Fit Catalytic Converter
- Magnaflow Standard Grade Direct-Fit Catalytic Converter
- Direct-Fit Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 1
- Inlet Gasket Included: No
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: No
- Heat Shield Attached: Yes
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 0
- Air Tube Adaptable: Yes
- California Air Resources Board (CARB) Certified: No
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 23689 helps keep the check engine light off. DIY installation is easy with the proper tools (no cutting or welding required). With features including mandrel-bent tubing to eliminate flow restrictions and stainless steel construction to resist corrosion, you can have confidence in the quality of this catalytic converter. Using state-of-the-art 3D scanning systems in the design process, the MagnaFlow metrology department ensures this new part to fit and function like the original equipment. This direct-fit catalytic converter is designed specifically for the 1981-1983 Mazda RX-7. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1983 - Mazda RX-7 | R | 1146 | Rear | 2 Cyl 1.1L | - |
Showing 1 - 7 of 7 products
Loading...