Image
Product
Price
- Rear of Catalyst - Federal ID=52mm; OD=65mm; Height=5mm
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Rear of Catalyst - Federal ID=52mm; OD=65mm; Height=5mm
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- From Manifold To Pipe
Additional Fitment Information:
| Vehicle |
|---|
| 1985 - Toyota Tercel |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Header flange
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Between Front Pipe & Exhaust Manifold
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
- Rear of Catalyst - Federal ID=52mm; OD=65mm; Height=5mm
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 1985 - Toyota Tercel | SR5 |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 5.5
- Body Height: 3.75
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 94041 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Toyota Tercel | L | 1452 | 4 Cyl 1.5L | - |
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1985 - Toyota Tercel | Converter To Front Pipe |
Showing 1 - 10 of 12 products
Loading...