Image
Product
Price
- Cut to Length, 5"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 60
- Weight Per Length: 11.70 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 600
- End 1 Inside Diameter:
- .625
- 16
- Material: Epdm
- End 2 Inside Diameter:
- .625
- 16
-
Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Get more out of your heater hose with Safety Stripe Heater Hose, constructed for extra-long service life. Intended for use on cars and light trucks, this EPDM hose is unaffected by most coolants, non-oil based coolant additives and high cooling system pressures. (Not recommended for heavy-duty trucks, buses, or off-road construction equipment; use Green Stripe heater hose for these applications.)
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0K55261B16C, 0K55261B22F, 10023264, 10230417, 10427731, 12322342, 12368235, 12575636, 12600099, 12604941, 12639709, 12639710, 14055JK20A, 15024548, 15051852, 15051853, 15064188, 15064189...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | L | 2389 | Pipe-1 To Engine | GAS | 4 Cyl 2.4L | - |
Additional Fitment Information:
| Vehicle | Prod. Date Range |
|---|---|
| 1995 - Nissan Pickup | To:12-00-95 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Inlet - Engine to Heater - Upper Hose at Engine
- Inlet - Engine to Heater
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Drive Type | CID |
|---|---|---|---|---|---|
| 1995 - Nissan Pickup | L | 2389 | 4 Cyl 2.4L | 4WD | - |
- Small I.D. Molded
- Outlet - Heater to Engine lower hose at engine
- Trim to Fit
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Drive Type | CID |
|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | 6 Cyl 3.0L | 4WD | 181 |
- Molded
- Outlet - Heater to Engine lower hose at engine
- Trim to Fit
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Drive Type | CID |
|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | 6 Cyl 3.0L | 4WD | 181 |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0935270131600, 10020, 10036781, 12637185, 14001S, 1405557Y12, 14055D4200, 140560B000, 140560B001, 140560S310, 1405610V11, 1405630P21, 1405630P24, 1405630R16, 1405640F04, 1405640F12, 1405653J07, 1405653J09...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | L | 2389 | Throttle Body To Pipe-1 | GAS | 4 Cyl 2.4L | - |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | Tee-1 To Pipe-1 | GAS | 6 Cyl 3.0L | 181 |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | Pipe-1 To Breather | GAS | 6 Cyl 3.0L | 181 |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | Tee-2 To Pipe-2 | GAS | 6 Cyl 3.0L | 181 |
Showing 1 - 9 of 9 products
Loading...