2018 Ford Catalytic Converter Parts
Choose a Model for your 2018 Ford
Image
Product
Price
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- CARB Compliant Direct Fit
- California C.A.R.B Compliant - Legal for sale and use in all 50 states
Additional Fitment Information:
| Vehicle | Aspiration |
|---|---|
| 2018 - Ford Focus | Naturally Aspirated |
- Direct-Fit Catalytic Converter
- Direct-Fit Catalytic Converter
- Direct-Fit OEM GRADE Federal (Excludes California)
- Product Attributes:
- Subtitle: Federal / Epa Compliant
This Part Fits the Following OEM/Substitute Numbers:
GL3Z 5E212-A, GL3Z5E212-A, GL3Z5E212A
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Left | 6 Cyl 3.5L | Limited | 213 |
- Direct-Fit Catalytic Converter
- Direct-Fit Catalytic Converter
- Direct-Fit OEM GRADE Federal (Excludes California)
- Product Attributes:
- Main Piping Diameter: 2.5
- Subtitle: Federal / Epa Compliant
This Part Fits the Following OEM/Substitute Numbers:
GL3Z 5E212-B, GL3Z5E212-B, GL3Z5E212B
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Right | 6 Cyl 3.5L | Platinum | 213 |
- OEM Grade Direct-Fit Catalytic Converter
- Magnaflow OEM Grade Direct-Fit Catalytic Converter
- Direct-Fit OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: No
- Tube Material: Stainless Steel
- Oxygen Sensor Location: Pre Converter And Midbed
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: Yes
- Heat Shield Attached: No
- Outlet Mounting Hardware Included: Yes
- CARB Executive Order Number: Not Applicable
- Overall Length: 39.125
- Body Type: Spun
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: Yes
- Sensor Port Count: 2
- Inlet Type: Bolt-on;clamp-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Outlet Type: Bolt-on
-
Features:
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- Torca AccuSeal® Exhaust Clamps provide a full 360-degree equally distributed clamping force preventing pipe distortion while creating a complete seal and maintaining serviceability
- OE-sized barbed exhaust hangers made from corrosion-resistant 410 stainless steel, designed to reduce noise and vibration
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Precision stamped collector design for optimal exhaust flow, engine efficiency, and fuel economy
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Simplifies installation with essential gaskets and hardware being included in the box
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Durable 308 stainless steel MIG welds
- Keep the check engine light off with MagnaFlow OEM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 21-470. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 2015-2020 Ford F-150 and interchanges with OE parts FL3Z-5E212-P and JL3Z-5E212-F. Hardware is included to eliminate the hassle of working with corroded factory parts. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
FL3Z 5E212-P, FL3Z-5E212-P, FL3Z5E212-P, FL3Z5E212P, JL3Z-5E212-F
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 4951 | Right | 8 Cyl 5.0L | 302 |
- OEM Grade Universal Catalytic Converter - 2.25in.
- Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.25in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Inlet Type: Weld-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Overall Length: 13
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.25
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 0
- Outlet Type: Weld-on
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51205 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2018 - Ford Explorer | L | 2300 | Rear | 4 Cyl 2.3L | 140 |
- OEM Grade Universal Catalytic Converter - 2.25in.
- with California Emissions System Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.25in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Inlet Type: Weld-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Overall Length: 13
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.25
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 0
- Outlet Type: Weld-on
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51205 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2018 - Ford C-Max | L | 1999 | 4 Cyl 2.0L | 122 |
- OEM Grade Direct-Fit Catalytic Converter
- Magnaflow OEM Grade Direct-Fit Catalytic Converter
- Direct-Fit OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: No
- Tube Material: Stainless Steel
- Oxygen Sensor Location: Pre Converter And Midbed
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: No
- Heat Shield Attached: No
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Overall Length: 25.75
- Body Type: Spun
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 2
- Inlet Type: Bolt-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Outlet Type: Clamp-on
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- Keep the check engine light off with MagnaFlow OEM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 21-474. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 2015-2020 Ford F-150 and interchanges with OE parts GL3Z-5E212-A and FL3Z-5E212-A. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
FL3Z-5E212-A, GL3Z 5E212-A, GL3Z-5E212-A, GL3Z5E212A
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Left | 6 Cyl 3.5L | King Ranch | 213 |
- OEM Grade Direct-Fit Catalytic Converter
- Magnaflow OEM Grade Direct-Fit Catalytic Converter
- Direct-Fit OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: No
- Tube Material: Stainless Steel
- Oxygen Sensor Location: Pre Converter And Midbed
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: Yes
- Heat Shield Attached: No
- Outlet Mounting Hardware Included: Yes
- CARB Executive Order Number: Not Applicable
- Overall Length: 42.75
- Body Type: Spun
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: Yes
- Sensor Port Count: 2
- Inlet Type: Bolt-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Outlet Type: Bolt-on
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Precision stamped collector design for optimal exhaust flow, engine efficiency, and fuel economy
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- Torca AccuSeal® Exhaust Clamps provide a full 360-degree equally distributed clamping force preventing pipe distortion while creating a complete seal and maintaining serviceability
- OE-sized barbed exhaust hangers made from corrosion-resistant 410 stainless steel, designed to reduce noise and vibration
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- Keep the check engine light off with MagnaFlow OEM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 21-475. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 2015-2020 Ford F-150 and interchanges with OE parts GL3Z-5E212-B and FL3Z-5E212-J. Hardware is included to eliminate the hassle of working with corroded factory parts. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
FL3Z-5E212-J, GL3Z 5E212-B, GL3Z-5E212-B, GL3Z5E212B
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Right | 6 Cyl 3.5L | Police Responder | 213 |
- OEM Grade Universal Catalytic Converter - 2.50in.
- Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.50in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Inlet Type: Weld-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Oxygen Sensor Location: Midbed
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Overall Length: 15
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.5
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.5
- Sensor Port Count: 1
- Outlet Type: Weld-on
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51356 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Left | 6 Cyl 3.5L | XL | 213 |
- OEM Grade Universal Catalytic Converter - 2.50in.
- Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.50in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Inlet Type: Weld-on
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Oxygen Sensor Location: Midbed
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Overall Length: 15
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.5
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.5
- Sensor Port Count: 1
- Outlet Type: Weld-on
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51356 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Sub Model | CID |
|---|---|---|---|---|---|---|
| 2018 - Ford F-150 | V | 3496 | Right | 6 Cyl 3.5L | Police Responder | 213 |
Showing 1 - 10 of 15 products
Loading...