Image
Product
Price
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 14.8
- 376
- End 1 Inside Diameter:
- 1.34
- 34
- Material: Epdm, Plastic
- Modular: No
- End 2 Inside Diameter:
- 1.34
- 34
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
215012Y000, 2150131U00, 2150131U10, 22183, 22312M, 254114D900, 62479, 71794, 8843, C71794, KM-3421, MR312255, MR355521
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Maxima | V | 2988 | Upper | GAS | 6 Cyl 3.0L | 182 |
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1995 - Nissan Altima | Upper |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Connector to Engine
- Lower (pipe to tstat)
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | Lower | 6 Cyl 3.0L | 181 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Pipe to Thermostat
- Lower (pipe to tstat)
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1995 - Nissan Pathfinder | Lower |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Production: -06/30/1995, Engine to Outlet Pipe
Additional Fitment Information:
| Vehicle | Position | Prod. Date Range |
|---|---|---|
| 1995 - Nissan 300ZX | Upper | To:06-30-95 |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Molded
- Production: -06/30/1995, Engine to Outlet Pipe
Additional Fitment Information:
| Vehicle | Position | Prod. Date Range |
|---|---|---|
| 1995 - Nissan 300ZX | Upper | To:06-30-95 |
- Molded
- Radiator to Connector
- Lower - Radiator to Pipe
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Drive Type | CID |
|---|---|---|---|---|---|---|
| 1995 - Nissan Pickup | V | 2960 | Lower | 6 Cyl 3.0L | 4WD | 181 |
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1995 - Nissan Pathfinder | Lower |
Additional Fitment Information:
| Vehicle | Position | Aspiration |
|---|---|---|
| 1995 - Nissan 300ZX | Upper | Naturally Aspirated |
Additional Fitment Information:
| Vehicle | Position | Aspiration |
|---|---|---|
| 1995 - Nissan 300ZX | Lower | Turbocharged |
Showing 1 - 10 of 39 products
Loading...