1988 Chevrolet S10 Exhaust Header Hedman
-
Features:
- Handcrafted, Mild Steel Construction.
- The Mid-Length Tube Header Design Provides Significantly More Low and Mid-range Power than Cast Manifolds, and Provide Better Ground Clearance And Component Compatibility Than Long Tube Headers.
- Ball & Socket Collector Design requires No Gasket, and Allows For More Exhaust System Misalignment than Old School, Gasket-Style Header Collectors
- Includes All The Necessary Mounting Hardware, Gaskets and Reducers (exhaust adapters)
- Limted Lifetime Warranty On Construction, Five Year Warranty on Factory-Applied Header Coating!
- Proud To Say, Made In The USA, Since 1954!
Hedman Hedders has been manufacturing quality headers in the USA since 1954, and they've been manufacturing Chevy S10, GMC S15, V8 engine swap specific headers for over 20 years. Each set uses mild steel, smooth flowing, CNC mandrel bent tubes, that are hand-welded to ensure each pair is identical to the next. Hedman's unique, gasketless ball and socket collector design allows your Small Block Chevy exhaust system to bolt up, even if it is not perfectly aligned with the header collectors.
These uncoated, MID-LENGTH TUBE headers are designed specifically for installing a Small Block Chevy 283-400 (Gen 1) engine into 1982-2004 Chevy S10/Blazer, GMC S15/Jimmy 2WD trucks. Fits both manual and automatic transmission trucks. The smooth 1-1/2 in. tube design provides ample exhaust flow to let your transplanted 283-400 SB Chevy engine breathe easy, and produce additional horsepower and torque over factory manifolds.
To ensure a proper installation, it is recommended that these headers be installed with Trans-Dapt Performance Product's #9906 engine swap mount kit.
These headers are uncoated, and ship from the factory with a temporary black paint that will burn off when submitted to normal operating temperatures. For protection against the element and lower underhood temperatures, these headers are also available with a silver or black ceramic-metallic finish.
Each set includes a pair of gaskets, header flange bolts and collector bolts. No collector gasket is needed.
Hedman Hedders is so confident in the quality of its headers that these headers are factory backed by a Limited Lifetime Warranty.
Additional Fitment Information:
| Vehicle | Region | Fuel Type | Drive Type |
|---|---|---|---|
| 1988 Chevrolet S10 | United States | GAS | RWD |
1 In Stock
$421.13 USD
$505.36 USD
- FREE SHIPPING on order over $100 USD shipped from same warehouse
- FULL WARRANTY
-
Order 24/7Order online anytime
-
100% SafetyOnly secure payments
-
Hot OffersDiscounts up to 90%
General
California Proposition 65
Warning: Cancer. For More Info Visit Www.p65warnings.ca.gov
Header Port Shape
Round
Quantity
Sold As A Pair.
with A.I.R. System
No
Cylinder Head
Stock Profile Heads
Tuned
No
Cylinder Head Port Shape
Round
Header Style
Mid-length Tube
Manual Transmission - Column
No
Flange Style
Standard
Collector Bolts Included
Yes
Bolts/Studs Included
Yes
Automatic Transmission - Floor
Yes
with EGR
No
Tube Material Thickness
- 16g
- 18g
Tube Diameter
1-1/2 In.
Automatic Transmission - Column
No
Head Type
Factory Heads
Package Contents
Headers, Ball And Socket Reducers (exhaust Adapters), Gaskets, Mounting Hardware
Reducer Outlet Size
2-1/2 In.
Tube Size
1-1/2 In.
Port Shape
Round
Tube Length
Mid-length Tubes
Manual Transmission - Floor
Yes
Collector Diameter
2-1/2 In.
Tube Style
Mid-length
Variations
69526, 69528
Drivetrain
2wd Only!
Collector Size
2-1/2 In.
Header Finish
Uncoated
Mounting Hardware Included
Yes
Weld-Up
No
Collector Attachment
2-1/2 In.
Header Fasteners Included
Yes
Use With
Trans Dapt. Motor Mount Kit #9906
Y-Pipe Included
No
Contents
Headers, Gaskets (when Applicable), 3-bolt Exhaust Adapters, Hardware
Finish Type
Uncoated Mild Steel
Notes
82-00 Gm S10/15, Blazer, Jimmy, Sonoma 2wd Sbc
Motor Mounts Included
No
Primary Tube Diameter (in)
1.50 In.
Crossover Pipe Included
No
Header Construction
- Mild Steel- Standard-duty
- Standard-duty
Replacement Head Flange Gasket
27500
Tube Design
- Mid-length
- Standard
Key Feature
2wd Only.
Power Steering
Yes
E.O. #
No
Exhaust System Dia
2-1/2 In.
Flange Thickness
- 0.25 In.
- 0.3125 In.
Engine
Chevy Sb 283-400 (gen 1) 1958-86
Air Conditioning
Yes
Installation Hardware Included
Yes
Reducers Included
Yes
Primary Tube Gauge
- 16g
- 18g
Header Material
Mild Steel
Title
Hedman Hedders Standard Uncoated Headers; 1-1/2 In. Tube Dia.; 2-1/2 In. Coll.; Stock Heads; Shorty Design
Catalytic Converter(s) Included
No
Replacement Gasket
27500
Collector Style
Ball And Socket Style (gasketless)
Emissions Notes
Not Legal For Street Use On '75-later Model Years! Legal For Off-road Use Only.
Packaging
bar code
732611695206
package quantity
1
length
20.00 in
width
13.50 in
height
8.25 in
weight
19.00 lb
Information on technical characteristics, the delivery set, the country of manufacture and the appearance
of the goods is for reference only and is based on the latest information available at the time of publication.
-
![]()
Very nice and good price thanks -
![]()
Fantastic finish and workmanship. Love the silver ceramic coating. -
![]()
They bolted right on with no issues, a perfect match. Unfortunately with the Flowmaster muffler I already had I did not notice a difference in sound. -
![]()
Would have been 5 stars if the instalation on the passenger side was not so tight! -
![]()
excelente -
![]()
great sounding headers for my impala and good exhaust flow mid range -
![]()
Great headers and super fast shipping!! -
![]()
Great fit. Easy to install without lifting engine. High quality finish and strong welds. Also has great ground clearance. Only drops to about even with cross-member under oil pan. My 9" sump pan now hangs about an inch lower than the headers. -
![]()
The headers fit great and cleared the frame. The outlet is below the transmission crossmember, so plan on that when you look at your exhaust. The paint burns off quickly if you are going bare, but it makes A LOT of smoke. Otherwise, sand blast and coat before you install. Came with flange gaskets and reducers. -
![]()
Do not start your engine in your garage after adding these!The black paint burns of and stinks like a nothing else! -
![]()
Great fit came on time and awesome look. I would recommend these for anyone in the market for a new set of headers. -
![]()
nice quality -
![]()
This are perfict for my low budget hot rod -
![]()
These went on a 84 c10 305 stock. The only issue I ran across was that the header on the pass side was hitting the metal fuel lines. I called Hedman and they said they have never heard of this issue. I was able to bend the fuel lines just enough to keep them from touching the header. Then I wrapped the fuel lines with heat reflective tape. No problem after about a month of driving. If you have the money get the ones already coated. I had these sand blasted and painted them with VHT Fireproof black, using their Fireproof primer also. I baked the paint on the headers using the mounted on vehicle method as recommended by Hedman, So far so good as far as the paint staying on. Just a pain to paint. Truck sounds awesome with true duals 2 1/2" pipe with 40 series Flowmasters. No cats. No H pipe or X pipe. Off road vehicle only. -
![]()
Quick delivery, perfect fit not one issue would definitely recommend, Not a huge performance gain but that wasn't expected, very neat and tidy. -
![]()
item came as described but had a heck of a time installing them in my 70 nova sb with a/c. Had to cutevaporator box at bottom to clear headers. The collectors were new for me but seem to seal quite well.Next time will try hooker comps -
![]()
I just ordered the wrong ones. I know several people who use these, get them powdered coated first or spray a very high temp coating/paint. Preparation is key to coating. -
![]()
I chose these partially due to pricing, but also the name. They look good, though I haven't completed the car as of yet to evaluate the overall performance factors. -
![]()
came quicker than i thought good quality even better that it came with the gaskets. love this product. i really recomend this product if you need good cheap headers -
![]()
They look and sound perfect. Fit was perfect. I recommend them to anyone who is looking for great American products!!! Fast shipment too!!! -
![]()
I snagged up these shorty headers after finding out that long tubes aren't CA legal. What an improvement in quality over the notoriously bad stock headers on my 2000's Mustang. No more exhaust leak whoo hoo! -
![]()
I'm happy with these overall. I did have some fitment issues so have to take off one star for that but with some coaxing, I finally got them all bolted up. I was happy I was able to buy american made product that didn't cost a fortune. Wish all my hotrod replacement parts were US made. -
![]()
Awesome! -
![]()
Very well constructed product. Will fit the AMC 304 currently in my CJ-7 as well as the AMC 401 that I am building to replace the 304 when it tires out. I like the under carriage exit leaving the vehicle to appear more stock. The the stubs that bolt to the lower plates of the manifolds are included in the set and will allow the manufacture and attachment of a custom exhaust system. These manifolds are sold as " uncoated " however, they are painted with a standard quality paint to prevent rust during shipping and storage. High temp would burn this coating off rapidly, so requires stripping prior to recoating with high temp paint or coating. The price is unbeatable, particularly when Free Shipping is taken into consideration.... -
![]()
These are a great value, mine have lasted over 20 years and never had any failed welds or any problems. Gas mileage improved about 10 percent and torque is noticeably greater. Never any issues with rust or corrosion and they sound great.Despite what the ad (and some rooky southern California smog techs) say, these hedders are legal in California on 6200 gvwr and higher pickups manufactuered before 1979, which are all classified as federal heavy duty emmisions vehicles and came stock without cat, egr, evap etc etc. -
![]()
CA SMOG LEGAL!!! nice product. Install is a PITA on both sides. The oil dipstick and tube will need to be removed and then modified to fit. or you can buy a flexable LOKAR setup. On the PASS side, be ready to ley over the engine and shoehorn these babies in. Getting them bolted to the mid pipe is a PITA also but overall a great product. It seals up well with the gasket provided. Just use a little high temp gasket maker on both sides to ensure a complete seal. The bolts go in easy and dont strip out like others. take your time and go easy, it will fit. They increase the sound and add som HP to the V6. Great when pair up with the DYNOMAX exhaust kit. -
![]()
The headers are not the chromed out version you see on the photo, but rather are the "Chikara" standards. However, they are good quality and you receive all the necessary equipment, bolts, O2 sensor rewire kit, individually packaged header gasket, collector gasket, and decals. If you have never done headers before than it comes with an instructional how to flyer and the steps one should take before and after attaching your equipment. Some of the black coat is coming off from being banged together during shipping, but overall I am extremely satisfied. My Talon now has better breathing and it really shows with this simple bolt on from Hedman!! -
![]()
Exactly what we were looking for, fixed the car right up and a few more days should be driving it! Thanks!
Related Products
Loading...