Image
Product
Price
- BD Chevy 2 Low UnLoc - 4wd 2015-2019 2500-3500 / 2014-2019 1500 / 2015-2020 SUV
- 4wd;
- BD Chevy 2 Low UnLoc - 2015-2019 2500-3500 4wd / 2014-2019 1500 4wd / 2015-2020 SUV 4wd
- 2 Low UnLoc
- Product Attributes:
- Category: Steering
- Engine: Gasoline
- Suggested Product: 1036627
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Installation is simple, the kit plugs in under the hood
- No wire cutting or splicing
- Kit comes with an illuminated rocker switch for control and to indicate when the front axle is being overridden
- Designed to allow the operator to manually disable the front wheel drive mechanism by holding the hubs in the free (2WD) mode with the transfer case in 4WD low range
- By allowing the front wheels to be disengaged, maximum torque is available to the rear wheels
- This will also allow for sharp "All The Way Over" turns without the front axle u-joint hopping or binding
- With this kit installed, the front wheels will NOT be driven through the transfer case
- Allows to have full power and torque while in a high gear reduction applied to the rear axle(s) only
- Vehicle maneuverability is reduced while in 4WD. When the 2Low Unloc is turned on, you disable the front wheel drive mechanism allowing for full torque to be available to the rear wheels only. The front wheels will NOT be driven, delivering normal 2WD maneuverability while in low range! This will also allow for sharp "All The Way Over" turns without the front axle u-joint hopping or binding.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Chevrolet Tahoe | V | 6162 | 8 Cyl 6.2L | 376 |
- BD Track Bar Bracket Ford F-250/F-350 SuperDuty 4wd 2008-2022
- 4wd; Lowers track bar mounting point by 2-inches;
- BD Track Bar Bracket Ford F-250/F-350 Superduty 4wd 2008-2022 (Gas & Diesel)
- Track Bar Bracket
- Product Attributes:
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1032110
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Ideal for 2-inch or 2.5-inch levelling kits
- Lowers track bar mounting point by 2-inches
- Corrects steering geometry on lifted vehicles
- Improves bump steer in levelled trucks
- High strength cast iron with ADI heat treat process for maximum strength
- Can be combined with BD 1032110/1032111 Track Bars for adjustability or larger lift height
- Common leveling and lift kits pull the trackbar out of position, affecting ride and steering quality, as well as axle position with respect to the body and frame. BD's track bar bracket relocates the pivot point 2-inch down lower down, offsetting the effect of the lift kit by bringing the trackbar assembly down into the factory position and fixing common steering and tracking issues. The BD track bar bracket is designed with high strength, ADI heat-treated cast iron for maximum strength and provides a strong reliable upgrade.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- Screamer Turbo Chevy/GM 6.6L L5P Duramax 2017-2024
- Screamer Turbo Chevy/GM 6.6L L5P Duramax 2017-2024 Silverado/Sierra 2500/3500
- Screamer L5P Turbo
- Product Attributes:
- Category: Single Turbo Performance
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1061825
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Increased airflow - up to 80lb/min
- Larger 66.2mm billet compressor wheel
- Larger 67mm turbine wheel
- Reduced EGTs at increased power output
- Stock appearing drop in turbo, will work with stock emissions equipment
- Up to 680hp with supporting modifications
- Includes intake horn
- BD's Screamer line of turbos offer drop-in, stock-appearing units that add an additional punch in power without major modifications to intake or exhaust systems. The L5P Screamer for 2017-up Duramax engines feature custom compressor and turbine wheels that have been designed to give you increased airflow without compromising on low end performance. Manufactured using OEM housings, the L5P Screamer turbo is machined to accept the new larger 66.2mm compressor and 67mm turbine wheels which will allow for better airflow (up to 80 lb./min) and lower exhaust gas temperatures. This turbo works best on trucks with supporting modifications such as custom tuning to maximize efficiency. With supporting modifications, the L5P Screamer can achieve up to 680hp.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - GMC Sierra 2500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- Turbo Mounting Kit HE300 RAM 6.7L Cummins 2019-up
- Turbo Mounting Kit HE300 RAM 6.7L Cummins 2019-2022
- Turbo Install Hardware
- Product Attributes:
- Category: Components
- Engine: 6.7l Cummins 19-up
- Suggested Product: 1045999
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- OE quality components
- Complete kit, no additional parts required
- This kit has all the necessary hardware for your stock or performance HE300 turbo install to help prevent leaks and to replace older studs that are prone to future breakage. Kits includes gaskets, studs and required hardware.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- INJECTOR CONNECTOR PIGTAIL KIT (4-PACK) CHEVY/GM L5P 2017+
- L5P engine;
- INJECTOR CONNECTOR PIGTAIL KIT (4-PACK) CHEVY/GM DURAMAX L5P 2017+
- Injector Connector 4-Pack
- Product Attributes:
- Category: Parts & Accessories
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1050457
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- 8-inch length
- Includes two heat shrink butt connectors
- Easy to install
- Exact fit
- A common failure point on the L5P Duramax, BD's replacement connector with pigtail for the fuel injectors will get you back on the road quickly. The connector is usually replaced at the same time as the injectors and is prone to increased resistance that can cause an injector DTC (P0201-P0208).
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - GMC Sierra 2500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- BD E-PAS Positive Air Shut-Off - Chevy/GM 3.0L Duramax 2019-2024
- BD E-PAS Positive Air Shut-Off - Chevy/GM 3.0L Duramax 2019-2024 Pick-Up/SUV
- Electronic Positive Air Shutdown
- Product Attributes:
- Category: Electronic Emergency Engine Shutdown
- Engine: Duramax 2.8l
- Suggested Product: 1057937
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Emergency Engine Shutdown
- Over speed shut down control utilizing built in Intake Air control valve
- Safely shuts your engine down if over speeding
- Can be installed in less than 1.5 hours
- Factory plug in connections and wiring harness
- Save 3 hours installation labor over mechanical systems
- Automatically resets after shut down
- Only the switch needs a tool to install
- Easily removed for truck lease returns
- Like a fire extinguisher in your house, or an earthquake kit, it's always better to be prepared. Although rare, Diesel Engine Runaway is caused when external hydrocarbons are drawn into the engine and can cause over speeding and catastrophic engine failure. Life, limb and your vehicle are put in jeopardy. BD Diesel Performance has you covered should the worst happen with our Electronic Positive Air Shutdown (E-PAS) units by cutting the intake air supply to the cylinders and safely shutting down the engine. The E-PAS controls the electronic throttle body in the intake manifold found on most late model diesel engines by closing it to shut off the air supply in emergency situations. The E-PAS can be easily installed in less than 1.5 hours with factory plug-in connectors and premade wiring harnesses. Automatically resets itself after shutdown and can be easily removed for truck lease returns.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - GMC Sierra 1500 | L | 2993 | 6 Cyl 3.0L | 183 |
- BD Screamer 6.7L Cummins Turbo RAM 2019-2022 Pick-up HE300VG
- CARB EO D-553-14
- BD Screamer 6.7L Cummins Turbo RAM 2019-2022 2500/3500 Pick-up HE300VG
- Screamer Turbo
- Product Attributes:
- Category: Stock Replacement
- Engine: 6.7l Cummins 19-up
- Suggested Product: 1057932
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- 50-STATE LEGAL!
- Enables quicker turbo response
- Replaces OEM Parts: 5456364, 5456365, 68444771AA, 68444771AB, 5498271RX, 5554227
- Ballistic Billet 64.5mm 7+7 blade compressor wheel and Low MOI QST 70mm 12 blade turbine wheel
- The QST Turbine wheel has a 15% reduction in MOI (moment of inertia) which results in quicker turbo response
- QST turbine Blade thickness decreased by 25% allowing for higher turbine gas flow and increased efficiency
- Each actuator is calibrated and tested prior to shipping
- VSR high speed balanced
- CARB EO No. D-553-14
- Allows for higher turbine gas flow & increased efficiency
- Can support modifications up to 690 HP
- Drops into the stock location
- Includes BD's HE300 Turbo Mounting Kit (PN: 1045999) with all the necessary hardware for your turbo install
- A drop-in stock installation, stock looking replacement that is anything but stock! The larger Ballistic Billet compressor wheel and our new exclusive Low MOI QST turbine wheel results in reduced backpressure, quicker response, increased efficiency and increased turbine flow compared to the competition. This results in increased maximum potential power output, right up to 690 horsepower with performance modifications. No extra parts to install, just drop-in and enjoy the extra power potential.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD Protect68 Gasket Plate Kit Dodge 6.7L 2019-2024 68RFE Transmission
- BD Protect68 Gasket and Separator Plate Kit Dodge 6.7L 2019-2022 68RFE Transmission
- Protect68 Gasket Plate Kit
- Product Attributes:
- Category: Shift & Pressure Controls
- Engine: 6.7l Cummins 19-up
- Suggested Product: 1071220x
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- Ideal for use with EFI Live, HP Tuners or other transmission pressure tuning
- Recommended full throttle max line pressure 225-250psi
- Custom bonded gasket valve body separator plate increases line pressure while stopping internal cross leaks
- Exclusive BD separator plate gaskets eliminate cross leaks and eliminate P0871 codes
- Heavy duty accumulator plate to prevent accumulator blowout
- Kit includes pan gasket, 3 doughnut seals and check ball
- This kit requires custom transmission tuning or an additional module to command higher line pressure
- Industry leading custom bonded gasket valve body separator plate substantially reduces cross leaks compared to stock and other aftermarket kits, even with much higher line pressures - up to 250psi. Kit includes a heavy duty accumulator plate to prevent accumulator blow-out. Ideal for use with EFI Live, HP Tuners, and other transmission pressure tuning.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- Track Bar Kit Ford F-250/F-350 4wd 2017-2022 & F-450/F-550 4wd/2wd 2017-2022
- 4wd;
- Track Bar Kit Ford SuperDuty F-250/F-350 4wd 2017-2022 & F-450/F-550 4wd/2wd 2017-2022
- Track Bar
- Product Attributes:
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1303104-kt
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Long lasting, easily serviceable polyurethane bushing
- No welded joints
- OEM Ball joint comes pre-installed
- Drive straighter with less wander and more positive steering feel
- Perfect solution for steering stability
- Helps resolve "Death Wobble
- Gas & Diesel
- Fully Adjustable
- No need to remove bar from the truck to adjust
- Adjustable to accommodate up to a 6-inch lift
- Made from high strength, heat treated forged components
- High quality black Cerakote finish, which resists corrosion and doesn't flake off like powder coat when hit by road debris
- BD's fully Adjustable Track Bar will fit stock trucks and accommodate those lifted up to 6-inches, plus, there is no need to remove the bar from the truck to adjust. The black Cerakote finished Adjustable Track Bar will allow for correct axle alignment on lifted trucks so they drive straighter with less wander and more positive steering feel. Installation kit comes with long lasting, easily serviceable polyurethane bushing. BD's Adjustable Track Bar is the perfect solution for steering stability.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Ford F-350 Super Duty | V | 6210 | 8 Cyl 6.2L | 379 |
- BD E-PAS Positive Air Shut-Off - Chevy/GM 6.6L Duramax L5P 2017-2024
- L5P engine;
- BD E-PAS Positive Air Shut-Off - Chevy/GM 6.6L Duramax L5P 2017-2024 2500HD / 3500HD & 2019-2023 4500HD / 5500HD / 6500HD
- Electronic Positive Air Shutdown
- Product Attributes:
- Category: Electronic Emergency Engine Shutdown
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1057937
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Emergency Engine Shutdown
- Over speed shut down control utilizing built in Intake Air control valve
- Safely shuts your engine down if over speeding
- Can be installed in less than 1.5 hours
- Factory plug in connections and wiring harness
- Save 3 hours installation labor over mechanical systems
- Automatically resets after shut down
- Only the switch needs a tool to install
- Easily removed for truck lease returns
- Like a fire extinguisher in your house, or an earthquake kit, it's always better to be prepared. Although rare, Diesel Engine Runaway is caused when external hydrocarbons are drawn into the engine and can cause over speeding and catastrophic engine failure. Life, limb and your vehicle are put in jeopardy. BD Diesel Performance has you covered should the worst happen with our Electronic Positive Air Shutdown (E-PAS) units by cutting the intake air supply to the cylinders and safely shutting down the engine. The E-PAS controls the electronic throttle body in the intake manifold found on most late model diesel engines by closing it to shut off the air supply in emergency situations. The E-PAS can be easily installed in less than 1.5 hours with factory plug-in connectors and premade wiring harnesses. Automatically resets itself after shutdown and can be easily removed for truck lease returns.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2020 - Chevrolet Silverado 3500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
Showing 1 - 10 of 101 products
Loading...