Image
Product
Price
- Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Center Outlet Mufflers Required Use Offset Inlet/Center Outlet Mufflers Only
- Tailpipe Set; Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Center Outlet Mufflers Required;
- Tailpipe Set
- Product Attributes:
- Tubing Diameter: 2.500 In.
- Automotive Item Grade: High Performance
- Exhaust Pipe Wall Max Gauge: 16
- Exit Position: Single Side
- Inlet Diameter: 2.500 In.
- System Type: Tailpipe
- WARNING CA Proposition 65: No
- Fitment: Direct Oe Replacement
-
Features:
- Mandrel Bent 16 Gauge Aluminized Tubing
- Exits At Rear Of Vehicle
- 3 Year Limited Warranty
- Premium Flowmaster Quality
- These Builder Series tailpipes are constructed from 2.50-inch mandrel-bent 16-gauge aluminized steel tubing for maximum flow, tuck up high in the chassis for good clearance and exit straight-out the back under the rear bumper. Designed to be used with Side Inlet/Center Outlet mufflers such as part# 942546 (Super 44 Series) or 942551 (50 Series) mufflers. Covered by our 3-year Limited Warranty. Note: Not designed to fit in factory bumper cutouts. Some fitment may be necessary. Does Not include installation hardware or exhaust tips.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Camaro | L | 4097 | 6 Cyl 4.1L | 250 |
- Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Offset Outlet Mufflers Required Use Offset Inlet/Offset Outlet Mufflers Only
- Tailpipe Set; Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Offset Outlet Mufflers Required;
- Tailpipe Set
- Product Attributes:
- Tubing Diameter: 2.500 In.
- Automotive Item Grade: High Performance
- Exhaust Pipe Wall Max Gauge: 16
- Exit Position: Single Side
- Inlet Diameter: 2.500 In.
- System Type: Tailpipe
- WARNING CA Proposition 65: No
- Fitment: Direct Oe Replacement
-
Features:
- Mandrel Bent 16 Gauge Aluminized Tubing
- Exits At Rear Of Vehicle
- Aluminized Steel
- Premium Flowmaster Quality
- 3 Year Limited Warranty
- These Builder Series tailpipes are constructed from 2.50-inch mandrel-bent 16-gauge aluminized steel tubing for maximum flow, tuck up high in the chassis for good clearance and exit straight-out the back under the rear bumper. Designed to be used with Side Inlet/Opposite Side Outlet mufflers such as part# 942548 (Super 44 Series) or 53058 (Super 50 Series) mufflers. Covered by our 3-year Limited Warranty. Note: Not designed to fit in factory bumper cutouts. Some fitment may be necessary. Does Not include installation hardware or exhaust tips.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Chevelle | L | - | 6 Cyl 4.1L | 250 |
- Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Center Outlet Mufflers Required
- Tailpipe Set; Single Side Exit; 2.5 in. Diameter Sold In Pairs; Hardware/Hangers Are Required For Installation; Offset Inlet/Center Outlet Mufflers Required;
- Tailpipe Set
- Product Attributes:
- Tubing Diameter: 2.500 In.
- Automotive Item Grade: High Performance
- Exhaust Pipe Wall Max Gauge: 16
- Exit Position: Single Side
- Inlet Diameter: 2.500 In.
- System Type: Tailpipe
- WARNING CA Proposition 65: No
- Fitment: Direct Oe Replacement
-
Features:
- Mandrel Bent 16 Gauge Aluminized Tubing
- Exits At Rear Of Vehicle
- 3 Year Limited Warranty
- Premium Flowmaster Quality
- These Builder Series tailpipes are constructed from 2.50-inch mandrel-bent 16-gauge aluminized steel tubing for maximum flow, tuck up high in the chassis for good clearance and exit straight-out the back under the rear bumper. Designed to be used with Side Inlet/Center Outlet mufflers such as part# 942546 (Super 44 Series) or 942551 (50 Series) mufflers. Covered by our 3-year Limited Warranty. Note: Not designed to fit in factory bumper cutouts. Some fitment may be necessary. Does Not include installation hardware or exhaust tips.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Camaro | V | 4949 | 8 Cyl 4.9L | 302 |
- Dual; Dual Rear Exit; Includes 2.5 in. Tubing/X-Member Back/H-Pipe/Hardware/Super 40 Series(TM) Mufflers;Legal On Non-Emissions Controlled Vehicles Or For Race Use
- American Thunder Header Back Exhaust System; Dual; Dual Rear Exit; Includes 2.5 in. Tubing/X-Member Back/H-Pipe/Hardware/Super 40 Series™ Mufflers;
- American Thunder Header Back Exhaust System
- Product Attributes:
- Tip Quantity: 0
- Tubing Diameter: 2.500 In.
- Exhaust Type: Dual
- Inlet Diameter: 2.500 In.
- Sound Level: Moderate/aggressive
- WARNING CA Proposition 65: No
- Exhaust Series: American Thunder
- Heat Shield Attached: No
- Exit Style: Straight
- Muffler Series: Super 40 Series
- Inlet Inside Diameter: N/a
- Outlet Outside Diameter: 2.500 In.
- Tail Pipe Diameter: 2.500 In.
- Exit Position: Dual Rear
- Tip Diameter: N/a
- Muffler Count: 2
- System Type: Header Back
- Muffler Part Number: 952548
-
Features:
- Mandrel Bent 16 Gauge Aluminized Tubing
- Moderate to Aggressive Exterior Exhaust Tone
- Includes Hangers And Hardware For Easy Installation
- Connects After Factory Catalytic Converter
- Premium Flowmaster Quality
- Made in the USA
- 3 Year Limited Warranty
- This American Thunder(R) crossmember-back exhaust system is custom designed for most 1964-1972 GM A-body cars and is for the person looking for a complete 2.50-inch dual exhaust system with a moderately aggressive exterior tone and a moderate interior sound. With easy fit in mind, these aluminized steel systems feature all mandrel-bent tubing, an H-pipe to equalize the exhaust pressures for maximum performance and deep sound and includes a pair of specially selected Super 40(TM) mufflers. The mandrel-bent 2.50-inch tailpipes tuck up out of the way for maximum clearance and offer you two choices of tailpipe exit styles. Like all Flowmaster(R) systems, benefits include improved throttle response, power, and mileage. Designed for an easy fit, these systems include all necessary parts and hardware for an easy installation and is covered by our 3-year Limited Warranty.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Chevelle | V | - | 8 Cyl 4.6L | 283 |
- Dual; Factory Location Exit; Includes 2.5 in. Tubing From Transmission X-Member Back/H-Pipe/Hardware/Super 44(TM) Delta Flow Mufflers;Legal On Non-Emissions Controlled Vehicles Or For Race Use Does Not Fit Convertibles w/o X-Brace Modification
- American Thunder Header Back Exhaust System; Dual; Factory Location Exit; Includes 2.5 in. Tubing From Transmission X-Member Back/H-Pipe/Hardware/Super 44™ Delta Flow Mufflers;
- American Thunder Header Back Exhaust System
- Product Attributes:
- Tip Quantity: 0
- Tubing Diameter: 2.500 In.
- Exhaust Type: Dual
- Inlet Diameter: 2.500 In.
- Sound Level: Moderate/aggressive
- WARNING CA Proposition 65: No
- Exhaust Series: American Thunder
- Heat Shield Attached: No
- Exit Style: Straight
- Muffler Series: Super 44 Series
- Inlet Inside Diameter: N/a
- Outlet Outside Diameter: 2.500 In.
- Tail Pipe Diameter: 2.500 In.
- Exit Position: Dual Side
- Tip Diameter: N/a
- Muffler Count: 2
- System Type: Header Back
- Muffler Part Number: 942546
-
Features:
- Mandrel Bent 16 Gauge Aluminized Tubing
- Moderate to Aggressive Exterior Exhaust Tone
- Includes Hangers And Hardware For Easy Installation
- Header Back System
- Premium Flowmaster Quality
- 3 Year Limited Warranty
- This American Thunder system is specially designed for 1967-1968 Camaro and Firebirds and is perfect for the person looking for a complete crossmember-back dual exhaust system. With an easy-fit in mind, this exhaust system is manufactured as a true dual exhaust using 2.50-inch aluminized steel tubing throughout, includes a built-in H-pipe design and delivers improved throttle response, power with a deep muscle car sound. The mandrel-bent tubing flows into a pair of Super 44 mufflers with 2.50-inch tailpipes exiting in the factory location behind the rear wheels pointing down just below the quarter panel. The system delivers a moderate to aggressive interior and exterior tone that's suited for the enthusiast who wants their performance to be heard. Designed for an easy fit, these systems include all necessary parts, hardware, and instructions. If you prefer Stainless steel construction, check out optional system# 817129. Notes: Fits convertibles by spacing down the factory convertible body brace by approximately .375-inch, or you can replace the factory body brace with a Hotchkis Performance body brace part #1404.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
15896, 15899, 817129
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Camaro | V | 6489 | 8 Cyl 6.5L | 396 |
- 2.5 Offset In/2.5 Offset Out; Clamp On; 409 Stainless Steel Not Direct Fit-Some Adaptation Required
- FlowFX Muffler; 2.5 Offset In/2.5 Offset Out; Clamp On; 409 Stainless Steel;
- FlowFX Muffler
- Product Attributes:
- Tip Quantity: 0
- Muffler Overall Length: 20.000 In.
- Muffler Type: Absorption
- Outlet Connection Type: Clamp-on
- Outlet Position: Offset (opposite)
- WARNING CA Proposition 65: Yes
- Muffler Body Width: 9.000 In.
- Muffler Series: Flow Fx
- Inlet Inside Diameter: 2.500 In.
- Muffler Body Length: 14.000 In.
- Main Piping Diameter: 2.500 In.
- Outlet Quantity: 1
- Inlet Quantity: 1
- Inlet Position: Offset
- Inlet Outside Diameter: 2.500 In.
- Inlet Connection Type: Clamp-on
-
Features:
- Not A Direct Fit
- Moderate Sound
- Straight Through Style
- Fully Welded Steel Case
- Flowmaaster's Flow FX series mufflers deliver a moderate performance tone for the enthusiast looking for an exhaust note that is different from the "chambered" muffler sound. The interior features a large 3.00-inch "straight-through" stainless steel perforated core, surrounded with high-temperature sound absorption materials delivering a deep traditional mellow tone. The internal flow design is reversible, so the muffler can be installed in either direction to best suit the vehicle application and offsets needed. Features include fully MIG-welded "bright" 409 stainless steel construction with the Flow FX logo embossed on both sides of the case. The Flow FX line of mufflers is perfect for the person looking for a show quality performance muffler at an economical price point and in a compact sized case.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Sub Model | CID |
|---|---|---|---|---|---|
| 1967 - Chevrolet Chevelle | V | 4638 | 8 Cyl 4.6L | SS | 283 |
- 40 Series™ Muffler
- 2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel
- 40 Series™ Muffler; 2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel;
- 40 Series(TM) Muffler
- Product Attributes:
- Tip Quantity: 0
- Automotive Item Grade: High Performance
- Muffler Type: Reflection
- California Proposition 65 Chemical Name 2: Chromium (hexavalent Compounds)
- Outlet Connection Type: Pipe
- California Proposition 65 Chemical Name 1: Nickel (metallic)
- Outlet Position: Offset
- Inlet Diameter: 2.250 In.
- Sound Level: Aggressive
- WARNING CA Proposition 65: Yes
- Fitment: Universal
- Body Width: 9.750 In.
- Muffler Series: 40 Series
- Inlet Inside Diameter: 2.250 In.
- Outlet Outside Diameter: 2.250 In.
- Main Piping Diameter: Oem
- Inlet Position: Offset
- Inlet Outside Diameter: 2.250 In.
- Inlet Connection Type: Pipe
-
Features:
- Durable Fully Welded 409 Stainless Steel
- Aggressive Sound Exterior Exhaust Tone
- Noticeable Interior Resonance
- Excellent Street/Strip And Off Road Application
- The Original 40 series muffler delivers an aggressive exterior and interior tone. If you're looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Caprice | V | 4638 | 8 Cyl 4.6L | 283 |
- 2.5 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel
- 40 Series™ Muffler; 2.5 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel;
- 40 Series™ Muffler
- Product Attributes:
- Tip Quantity: 0
- Automotive Item Grade: High Performance
- Muffler Type: Reflection
- Outlet Connection Type: Pipe
- Outlet Position: Center
- Inlet Diameter: 2.500 In.
- Sound Level: Aggressive
- WARNING CA Proposition 65: Yes
- Fitment: Universal
- Body Width: 9.750 In.
- Muffler Series: 40 Series
- Inlet Inside Diameter: 2.500 In.
- Outlet Outside Diameter: 2.500 In.
- Main Piping Diameter: Oem
- Inlet Position: Offset
- Inlet Outside Diameter: 2.500 In.
- Inlet Connection Type: Pipe
-
Features:
- 409 Stainless Steel
- Limited Lifetime Warranty
- Aggressive And Powerful Exterior Exhaust Tone
- Notable Interior Resonance
- Excellent Street/Strip And Off Road Application
- No Internal Packing To Blowout
- The Original Two Chamber Design
- Premium Flowmaster Quality
- The Original 40 series muffler delivers an aggressive exterior and interior tone. If you're looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Corvette | V | 6998 | 8 Cyl 7.0L | 427 |
- 2.25 Offset In/2.25 Offset Out; Clamp On; 409 Stainless Steel Not Direct Fit-Some Adaptation Required
- FlowFX Muffler; 2.25 Offset In/2.25 Offset Out; Clamp On; 409 Stainless Steel;
- FlowFX Muffler
- Product Attributes:
- Tip Quantity: 0
- Muffler Overall Length: 20.000 In.
- Muffler Type: Absorption
- Outlet Connection Type: Clamp-on
- Outlet Position: Offset (opposite)
- WARNING CA Proposition 65: Yes
- Muffler Body Width: 9.000 In.
- Muffler Series: Flow Fx
- Inlet Inside Diameter: 2.250 In.
- Muffler Body Length: 14.000 In.
- Main Piping Diameter: 2.250 In.
- Outlet Quantity: 1
- Inlet Quantity: 1
- Inlet Position: Offset
- Inlet Outside Diameter: 2.250 In.
- Inlet Connection Type: Clamp-on
-
Features:
- Not A Direct Fit
- Moderate Sound
- Straight Through Style
- Fully Welded Steel Case
- Flowmaster's Flow FX series mufflers deliver a moderate performance tone for the enthusiast looking for an exhaust note that is different from the "chambered" muffler sound. The interior features a large 3.00-inch "straight-through" stainless steel perforated core, surrounded with high-temperature sound absorption materials delivering a deep traditional mellow tone. The internal flow design is reversible, so the muffler can be installed in either direction to best suit the vehicle application and offsets needed. Features include fully MIG-welded "bright" 409 stainless steel construction with the Flow FX logo embossed on both sides of the case. The Flow FX line of mufflers is perfect for the person looking for a show quality performance muffler at an economical price point and in a compact sized case.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Caprice | V | 6998 | 8 Cyl 7.0L | 427 |
- 2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel
- 40 Series™ Muffler; 2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel;
- 40 Series™ Muffler
- Product Attributes:
- Tip Quantity: 0
- Automotive Item Grade: High Performance
- Muffler Type: Reflection
- Outlet Connection Type: Pipe
- Outlet Position: Offset
- Inlet Diameter: 2.250 In.
- Sound Level: Aggressive
- WARNING CA Proposition 65: Yes
- Fitment: Universal
- Body Width: 9.750 In.
- Muffler Series: 40 Series
- Inlet Inside Diameter: 2.250 In.
- Outlet Outside Diameter: 2.250 In.
- Main Piping Diameter: Oem
- Inlet Position: Offset
- Inlet Outside Diameter: 2.250 In.
- Inlet Connection Type: Pipe
-
Features:
- Durable Fully Welded 409 Stainless Steel
- Aggressive Sound Exterior Exhaust Tone
- Noticeable Interior Resonance
- Excellent Street/Strip And Off Road Application
- The Original 40 series muffler delivers an aggressive exterior and interior tone. If you're looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1967 - Chevrolet Caprice | V | 6489 | 8 Cyl 6.5L | 396 |
Showing 1 - 10 of 47 products
Loading...