Image
Product
Price
- Adjustable Rear Sway Bar End Links
- Not compatible with aftermarket sway bars Requires Front 3" to 6" of Lift Rear 0" to 6" of Lift
- Adjustable Rear Sway Bar End Links | Wrangler JK and JL
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 8.75
- Installation Time: 1-3
- Installation Difficulty: Moderate
- Maximum Adjusted Length: 15.00
- Title: Adjustable Rear Sway Bar End Links
-
Features:
- Correct sway bar geometry on lifted vehicles and improve suspension performance on- and off-road
- Maintain proper balance between front and rear sway bars for safer, more predictable on-road driving
- Tension-free rod ends offer 45 degrees of mounting alignment for reduced wear on related components
- Variable length design allows you to accurately set sway bar operating angle
- Special zinc plating applied for corrosion resistance and long lasting protection
- Also fits Wrangler JK right hand drive models
- Retain the handling of your Jeep Wrangler JK with rear adjustable sway bar links to retain proper sway geometry after lifting your Jeep. The adjustable rear sway bar end links allow for proper use of the rear sway bar and improve handling on and off road. A common misconception among Jeep owners is that the rear sway bar is unnecessary off-road and should be removed. This is not true however, as the rear sway bar is small and flexible enough to allow plenty of suspension articulation.
Additional Fitment Information:
| Vehicle | Position | Region | Sub Model |
|---|---|---|---|
| 2013 - Jeep Wrangler | Rear | United States | Sport |
- Adventure Series FOX 2.0 Front Shock
- 2.5-3.5" Lift
- Application specific valving to maximize performance
- FOX 2.0 Front Shock | Adventure Series | 2.5"-3.5" Lift | Wrangler JK
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Title: Adventure Series Fox 2.0 Front Shock
-
Features:
- Internal Floating Piston (IFP) separates the shock oil from the nitrogen charged gas chamber
- Large 5/8" alloy steel shock shaft for increased strength
- Shafts are hard chrome plated and heat-treated to resist pitting and scratches
- Maximum performance from the factory-tuned precision valving
- Upgrade your Jeep Wrangler JK with a set of FOX 2.0 Adventure Series IFP front shocks. PN 984-50-351 is designed specifically for the front of your Jeep in conjunction with a 2.5"-3.5" lift. FOX 2.0 Adventure Series IFP shocks improve ride quality on the street and performance when heading into the unknown. The affordable monotube design is far superior to any twin-tube shock competitor. Monotube damping technology means that the largest possible piston size for controlling damping force within the 2" diameter steel bodies. Large hard-chrome plated and heat treated 5/8" steel shock shafts adds strength and rigidity. FOX Internal Floating Piston (IFP) technology separates the shock oil from the high-pressure, nitrogen-charged gas chamber. IFP eliminates oil aeration allowing maximum performance from the factory-tuned precision valving. Fox's bolt on, 2.0 Adventure Series IFP shocks improve your driving experience in any terrain. Matching rear shocks are available -- PN FOX98450359 (2.5"-3.5" lift)
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Position | Region |
|---|---|---|
| 2013 - Jeep Wrangler | Front | United States |
- Quicker Disconnect Sway Bar Links
- Min. Adjusted Length - 8" Max Adjusted Length - 11.625" *See Instructions for further details. Not compatible with aftermarket sway bars. Some vehicles may require extended front brake hoses or other modifications to compensate for additional suspension travel.
- JKS Quicker Disconnect sway bar end links fit Wrangler JK Jeeps with 0-6" lift. Get up to 30% better articulation on uneven terrain. Quick-release pins make it easy to decouple your sway bar. The adjustable-length design is 100% bolt-on and attaches to your sway bar and axle housing. Made in the USA, JKS Quicker Disconnects are powder-coated and built to last. Sold in pairs.
- In the box: All Necessary Mounting / Installation Hardware Sway Bar Links
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 8.00
- For Use With Lift Heights: 2.5"-6"
- Installation Time: 1-2
- Horizontal Position: Front
- Installation Difficulty: Moderate
- Is Adjustable: Yes
- Length: 8 To 11-5/8
- Maximum Adjusted Length: 11.625
- Title: Quicker Disconnect Sway Bar Links
- Installation Tools Requirements: Angle Measuring Tool; Factory Service Manual (recommended); Grease Gun With Zerk Fitting Coupler; Medium Strength Threadlocker; Metric/standard Socket Wrench Set; Torque Wrench; Wheel Bearing Grease
-
Features:
- Fits vehicles with 2.5"-6.0" Lift Only
- Gain up to 30 percent more axle articulation by disconnecting your front sway bar
- Also fits Wrangler JK right hand drive models
- Dramatically improve off-road performance on stock or modified Jeeps
- Variable length design adapts to your vehicle and future modifications
- Convenient grease fittings ensure easy bushing lubrication for smooth, silent operation
- Stainless tapered mounting posts and self-align bushings allow you to connect or disconnect on unlevel surfaces
- Spherical bushings provide unrestricted 360 degrees of rotation and 11 degrees of misalignment capability
- JKS Quicker Disconnect sway bar end links fit Wrangler JK Jeeps with 0-6" lift. Get up to 30% better articulation on uneven terrain. Quick-release pins make it easy to decouple your sway bar. The adjustable-length design is 100% bolt-on and attaches to your sway bar and axle housing. Made in the USA, JKS Quicker Disconnects are powder-coated and built to last. Sold in pairs.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - Jeep Wrangler JK |
- Front Adjustable Track Bar
- Suggested Starting Length - 33.25" Min. Adjusted Length - 32.2" Max Adjusted Length - 34.2" *See Instructions for further details. Does NOT fit Right Hand Drive
- JKS adjustable front track bar for Jeep Wrangler JK provides added strength and adjustability. Fine tune track bar length to suit your combination of suspension components and ride height. Features precision 1-1/4" fine threads, 3/8"- wall 1.5" diameter DOM CNC-bent tubing with powder coated and zinc finish. Heavy duty rubber bushings at both ends provide quiet, vibration-free operation. For JK with up to 6" lift. Bolt-on installation. Does NOT fit right hand drive JK.
- In the box: All Necessary Mounting / Installation Hardware Track Bar
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 32.20
- For Use With Lift Heights: 1-6"
- Installation Time: 2-3
- Horizontal Position: Front
- Installation Difficulty: Moderate
- Is Adjustable: Yes
- Maximum Adjusted Length: 34.20
- Title: Front Adjustable Track Bar
- Suggested Starting Length: 33.25
-
Features:
- Superior quality replacement for original fixed length panhard rod
- Variable length design properly aligns axle housing with chassis and prevents undue stress on related components
- Fine adjustment threads enable ultra precise axle positioning
- Extremely strong DOM tube construction utilizes OE bends for correct geometry and clearance
- Premium grade rubber bushings ensure long-lasting comfort and quietness
- Zinc plated and powder coated for protection from corrosion and debris
- JKS adjustable front track bar for Jeep Wrangler JK provides added strength and adjustability. Fine tune track bar length to suit your combination of suspension components and ride height. Features precision 1-1/4" fine threads, 3/8"- wall 1.5" diameter DOM CNC-bent tubing with powder coated and zinc finish. Heavy duty rubber bushings at both ends provide quiet, vibration-free operation. For JK with up to 6" lift. Bolt-on installation. Does NOT fit right hand drive JK.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - Jeep Wrangler JK |
- Quicker Disconnect Sway Bar Links
- Not compatible with aftermarket sway bars Some vehicles may require extended front brake hoses or other modifications to compensate for additional suspension travel 2.5-6" Lift
- Quicker Disconnect Sway Bar Links | 2.5"-6.0" Lift | Wrangler JK
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 8.00
- Installation Time: 1-2
- Installation Difficulty: Moderate
- Maximum Adjusted Length: 11.625
- Title: Quicker Disconnect Sway Bar Links
- Installation Tools Requirements: Angle Measuring Tool; Factory Service Manual (recommended); Grease Gun With Zerk Fitting Coupler; Medium Strength Threadlocker; Metric/standard Socket Wrench Set; Torque Wrench; Wheel Bearing Grease
-
Features:
- Fits vehicles with 2.5"-6.0" Lift Only
- Gain up to 30 percent more axle articulation by disconnecting your front sway bar
- Also fits Wrangler JK right hand drive models
- Dramatically improve off-road performance on stock or modified Jeeps
- Variable length design adapts to your vehicle and future modifications
- Convenient grease fittings ensure easy bushing lubrication for smooth, silent operation
- Stainless tapered mounting posts and self-align bushings allow you to connect or disconnect on unlevel surfaces
- Spherical bushings provide unrestricted 360 degrees of rotation and 11 degrees of misalignment capability
- JKS Quicker Disconnect sway bar end links fit Wrangler JK Jeeps with 0-6" lift. Get up to 30% better articulation on uneven terrain. Quick-release pins make it easy to decouple your sway bar. The adjustable-length design is 100% bolt-on and attaches to your sway bar and axle housing. Made in the USA, JKS Quicker Disconnects are powder-coated and built to last. Sold in pairs.
Additional Fitment Information:
| Vehicle | Region |
|---|---|
| 2013 - Jeep Wrangler | United States |
- Quicker Disconnect Sway Bar Links
- Min. Adjusted Length - 5.625" Max Adjusted Length - 7.125" *See Instructions for further details. Not compatible with aftermarket swaybars. Some vehicles may require extended front brake hoses or other modifications to compensate for additional suspension travel.
- JKS Quicker Disconnect sway bar end links fit Wrangler JK Jeeps with 0-2" lift. Get better articulation on uneven terrain. Quick-release pins make it easy to decouple your sway bar. The adjustable-length design is 100% bolt-on and attaches to your sway bar and axle housing. Made in the USA, JKS Quicker Disconnects are powder-coated and built to last. Sold in pairs.
- In the box: All Necessary Mounting / Installation Hardware Sway Bar Links
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 5.625
- For Use With Lift Heights: 0-2"
- Installation Time: 1-2
- Horizontal Position: Front
- Installation Difficulty: Moderate
- Is Adjustable: Yes
- Length: 5-1/2 To 7-1/8
- Maximum Adjusted Length: 7.125
- Title: Quicker Disconnect Sway Bar Links
-
Features:
- Fits vehicles with 0"-2" Lift Only
- Gain 30 percent more axle articulation by disconnecting your front swaybar
- Also fits Wrangler JK right hand drive models
- Dramatically improve off-road performance on stock or modified Jeeps
- Variable length design adapts to your vehicle and future modifications
- Convenient grease fittings ensure easy bushing lubrication for smooth, silent operation
- Stainless tapered mounting posts and self-align bushings allow you to connect or disconnect on unlevel surfaces
- Spherical bushings provide unrestricted 360 degrees of rotation and 11 degrees of misalignment capability
- JKS Quicker Disconnect sway bar end links fit Wrangler JK Jeeps with 0-2" lift. Get better articulation on uneven terrain. Quick-release pins make it easy to decouple your sway bar. The adjustable-length design is 100% bolt-on and attaches to your sway bar and axle housing. Made in the USA, JKS Quicker Disconnects are powder-coated and built to last. Sold in pairs.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - Jeep Wrangler JK |
- Drag Link Flip Kit
- 3"+ Lift Requires 3" of front bump stop extension, JKS1130 available separately Should not be combined with other track bar relocation system Can be used with factory replacement adjustable track bars To be used with factory pitman arm for proper geometry Requires 17" diameter wheel or larger, with 4.75" backspacing or less
- Drag Link Flip Kit | Wrangler JK
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Title: Drag Link Flip Kit
-
Features:
- Provide better performing, solid steering feel
- Flattens out steering angle when combined with 2" lift or more
- 7/8" Step Drill Bit Included
- JKS Manufacturing’s Drag Link Flip kit for JK Wranglers consists of a new drag link, a Track Bar bracket and a tapered steering arm insert. The design flattens out steering angles with lift heights of 3" and above, while providing correct geometry to increased droop travel. Bringing angles back to stock with the increased ride height of a lift removes the bump steer commonly associated with lifted solid axle suspensions. Drilling is required with the supplied 7/8” step bit. 3" tall front aluminum bump stop extensions are necessary for proper clearance at full bump. JKS1130 extensions available separately.
Additional Fitment Information:
| Vehicle | Region |
|---|---|
| 2013 - Jeep Wrangler | United States |
- Adjustable Rear Track Bar
- 0-6" Lift Rear Trackbar Brace [JKS PN: OGS169] is strongly recommended to reinforce weak factory mount on axle. Trackbar Brace fits Left Hand Drive Models Only
- Adjustable Rear Track Bar | Wrangler JK
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 39.43
- Installation Time: 6
- Installation Difficulty: Moderate
- Maximum Adjusted Length: 42.43
- Title: Adjustable Rear Track Bar
- Suggested Starting Length: 40.38
-
Features:
- Zinc plated and powder coated for protection from corrosion and debris
- Also fits Wrangler JK right hand drive models
- Superior quality replacement for original fixed length panhard rod
- Variable length design properly aligns axle housing with chassis and prevents undue stress on related components
- Fine adjustment threads enable ultra precise axle positioning
- Extremely strong DOM tube construction utilizes OE bends for correct geometry and clearance
- Premium grade rubber bushings ensure long-lasting comfort and quietness
- Install a new adjustable rear track bar on your RHD Jeep Wrangler JK to properly align and control lateral axle movement left to right. The heavy duty track bar can be adjusted to suit your combination of suspension components and ride height. Features precision 1-1/4" fine threads, thick wall DOM CNC-bent tubing and powder coated and zinc finish. Heavy-duty rubber bushings at both ends provide quiet, vibration-free operation. Fits right hand drive JK only with up to 6" lift. Bolt-on installation.
Additional Fitment Information:
| Vehicle | Position | Region |
|---|---|---|
| 2013 - Jeep Wrangler | Rear | United States |
- Drag Link Flip Kit
- For use on LHD JK models with at least 2" of suspension lift Requires 3" of front bump stop extension, JKS1130 available separately Should not be combined with other track bar relocation system Can be used with factory replacement adjustable track bars To be used with factory pitman arm for proper geometry Requires 17" diameter wheel or larger, with 4.75" backspacing or less
- JKS Manufacturing?s Drag Link Flip kit for JK Wranglers consists of a new drag link, a Track Bar bracket and a tapered steering arm insert. The design flattens out steering angles with lift heights of 3" and above, while providing correct geometry to increased droop travel. Bringing angles back to stock with the increased ride height of a lift removes the bump steer commonly associated with lifted solid axle suspensions. Drilling is required with the supplied 7/8? step bit. 3" tall front aluminum bump stop extensions are necessary for proper clearance at full bump. JKS1130 extensions available separately.
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Title: Drag Link Flip Kit
-
Features:
- Provide better performing, solid steering feel
- Flattens out steering angle when combined with 2" lift or more
- 7/8" Step Drill Bit Included
- JKS Manufacturing’s Drag Link Flip kit for JK Wranglers consists of a new drag link, a Track Bar bracket and a tapered steering arm insert. The design flattens out steering angles with lift heights of 3" and above, while providing correct geometry to increased droop travel. Bringing angles back to stock with the increased ride height of a lift removes the bump steer commonly associated with lifted solid axle suspensions. Drilling is required with the supplied 7/8” step bit. 3" tall front aluminum bump stop extensions are necessary for proper clearance at full bump. JKS1130 extensions available separately.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - Jeep Wrangler JK |
- Adjustable Rear Track Bar
- Suggested Starting Length - 40.38" Min. Adjusted Length - 39.43" Max Adjusted Length - 42.43" *See Instructions for further details. Fits 0 to 6.0 in. suspension lift. Rear Trackbar Brace [JKS PN: OGS169] is strongly recommended to reinforce weak factory mount on axle. Trackbar Brace fits Left Hand Drive Models Only.
- Install a new adjustable rear track bar on your RHD Jeep Wrangler JK to properly align and control lateral axle movement left to right. The heavy duty track bar can be adjusted to suit your combination of suspension components and ride height. Features precision 1-1/4" fine threads, thick wall DOM CNC-bent tubing and powder coated and zinc finish. Heavy-duty rubber bushings at both ends provide quiet, vibration-free operation. Fits right hand drive JK only with up to 6" lift. Bolt-on installation.
- In the box: All Necessary Mounting / Installation Hardware Track Bar
- Product Attributes:
- California Proposition 65: ! Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Minimum Adjusted Length: 39.43
- For Use With Lift Heights: 0-6"
- Installation Time: 6
- Horizontal Position: Rear
- Installation Difficulty: Moderate
- Is Adjustable: Yes
- Maximum Adjusted Length: 42.43
- Title: Adjustable Rear Track Bar
- Suggested Starting Length: 40.38
-
Features:
- Zinc plated and powder coated for protection from corrosion and debris
- Also fits Wrangler JK right hand drive models
- Superior quality replacement for original fixed length panhard rod
- Variable length design properly aligns axle housing with chassis and prevents undue stress on related components
- Fine adjustment threads enable ultra precise axle positioning
- Extremely strong DOM tube construction utilizes OE bends for correct geometry and clearance
- Premium grade rubber bushings ensure long-lasting comfort and quietness
- Install a new adjustable rear track bar on your RHD Jeep Wrangler JK to properly align and control lateral axle movement left to right. The heavy duty track bar can be adjusted to suit your combination of suspension components and ride height. Features precision 1-1/4" fine threads, thick wall DOM CNC-bent tubing and powder coated and zinc finish. Heavy-duty rubber bushings at both ends provide quiet, vibration-free operation. Fits right hand drive JK only with up to 6" lift. Bolt-on installation.
Additional Fitment Information:
| Vehicle |
|---|
| 2013 - Jeep Wrangler JK |
Showing 1 - 10 of 14 products
Loading...