1987 Ford Timken Parts
Image
Product
Price
- Tapered Roller Bearing Cone and Cup Assembly
- Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Drive Type | CID |
|---|---|---|---|---|---|---|
| 1987 - Ford Mustang | V | - | Front Inner | 8 Cyl 5.0L | RWD | 302 |
- Tapered Roller Bearing Cone and Cup Assembly
- Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Trans Type | Block | CC | Transmission | Position | Engine | Trans. Speed | Transmission Manuf. Code | CID |
|---|---|---|---|---|---|---|---|---|---|
| 1987 - Ford Mustang | Transmission | V | - | Manual | Front | 8 Cyl 5.0L | 5 | T5 | 302 |
- Grease/Oil Seal
- Dana/Spicer 35 Axle
- Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 1987 - Ford Ranger | Front | 4WD |
- Grease/Oil Seal
- 3,750 lb. Axle
- Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 1987 - Ford E-150 Econoline Club Wagon | Rear | RWD |
- Grease/Oil Seal
- 9 in. Ring Gear
- Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 1987 - Ford Bronco | Rear | 4WD |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Rear
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1987 - Ford Country Squire | Rear |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- with 7.5" & 8.8" Ring Gear Differential
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1987 - Ford Thunderbird | Rear |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- with Sterling Axle
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1987 - Ford Aerostar | Rear |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1987 - Ford LTD Crown Victoria | Rear |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Sterling Axle
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1987 - Ford Aerostar | Rear |
Showing 1 - 10 of 42 products
Loading...