Image
Product
Price
- For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;CARB E.O. D-550-34
- Electric Fuel Pump; For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;
- Electric Fuel Pump
- Product Attributes:
- Hose Size: 0.3125 In.
- Maximum PSI: 3.5
- WARNING CA Proposition 65: Yes
- Fuel Type: Gasoline
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Inlet Size: 0.125 In. Npt
- Free Flow GPH: 28
- Item Weight: 1.200 Lbs.
-
Features:
- Solid-state Worry Free Electronics
- Internal Pressure Regulating
- Universal Design Allows For Easy Installation
- No Diaphragms Or Mechanical Parts To Wear Out
- They Make An Excellent Fuel Transfer Pump
- Gravity fed type pump with simple two-wire design. Works on 12 Volt negative ground systems only. Includes fittings and mounting hardware along with easy to follow DIY instructions. Pumps require approximately one amp average draw at maximum delivery. Flow rate is 28 gallons per hour (GPH) at 2 to 3-1/2 pounds per square inch (PSI). Universal design for most import 4 & 6-cylinder carburetor applications. Please see part #12S for V8 gasoline applications, part #12D for diesel applications or part #12E for Ethanol, Methanol, E85 and Race Fuel applications. Solid-state worry free electronics. Eliminates vapor lock and flooding. Works well as a fuel transfer, booster, or stand-alone pump. Not recommended for diesel, methanol, ethanol, E85 or race fuel applications!!
Additional Fitment Information:
| Vehicle |
|---|
| 1983 - Subaru GL |
- For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;CARB E.O. D-550-34
- Electric Fuel Pump; For Use w/Carburetor; Import; 2-3.5 psi; 42 gph; This Is Not An OEM Replacement Part;
- Electric Fuel Pump
- Product Attributes:
- Hose Size: 0.3125 In.
- Maximum PSI: 3.5
- WARNING CA Proposition 65: Yes
- Fuel Type: Gasoline
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Inlet Size: 0.125 In. Npt
- Free Flow GPH: 28
- Item Weight: 1.200 Lbs.
-
Features:
- Solid-state Worry Free Electronics
- Internal Pressure Regulating
- Universal Design Allows For Easy Installation
- No Diaphragms Or Mechanical Parts To Wear Out
- They Make An Excellent Fuel Transfer Pump
- Gravity fed type pump with simple two-wire design. Works on 12 Volt negative ground systems only. Includes fittings and mounting hardware along with easy to follow DIY instructions. Pumps require approximately one amp average draw at maximum delivery. Flow rate is 28 gallons per hour (GPH) at 2 to 3-1/2 pounds per square inch (PSI). Universal design for most import 4 & 6-cylinder carburetor applications. Please see part #12S for V8 gasoline applications, part #12D for diesel applications or part #12E for Ethanol, Methanol, E85 and Race Fuel applications. Solid-state worry free electronics. Eliminates vapor lock and flooding. Works well as a fuel transfer, booster, or stand-alone pump. Not recommended for diesel, methanol, ethanol, E85 or race fuel applications!!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Sub Model | CID |
|---|---|---|---|---|---|
| 1983 - Subaru Brat | H | 1781 | 4 Cyl 1.8L | GL | - |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Intake
Additional Fitment Information:
| Vehicle |
|---|
| 1983 - Subaru GL |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- CRITICAL NOTE: Alleged Fuel Pump Failures Can Often Be Traced to a Faulty Fuel Pressure Regulator Instead of (or In Addition to) The Pump Itself. To Avoid Unnecessary Warranty Returns and Comebacks, WORLDPAC Strongly Recommends Testing the Fuel Pressure, Volume and Pressure Regulator (If Equipped) Before Considering the Diagnosis of a Faulty Fuel Pump to be Complete and Correct.
Additional Fitment Information:
| Vehicle |
|---|
| 1983 - Subaru Brat |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Drive Type |
|---|---|
| 1983 - Subaru GL | 4WD |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Excludes 1.8L Engines with Carter brand carb.
Additional Fitment Information:
| Vehicle | Drive Type |
|---|---|
| 1983 - Subaru GL | FWD |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Aspiration |
|---|---|
| 1983 - Subaru Brat | Naturally Aspirated |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- 2 per Engine
Additional Fitment Information:
| Vehicle | Aspiration |
|---|---|
| 1983 - Subaru Brat | Naturally Aspirated |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Hitachi Carburator - 2 per Engine
Additional Fitment Information:
| Vehicle | Drive Type |
|---|---|
| 1983 - Subaru GL | FWD |
Showing 1 - 9 of 9 products
Loading...