Image
Product
Price
- Cut to fit
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 124
- 4.9
- End 1 Inside Diameter:
- .61
- 15
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- .61
- 15
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0491210631, 1, 10042686, 1010, 10120087, 122310, 12604942, 1333180, 1370436, 14-1725-8, 142-0801, 142-5941, 14207S, 1489658, 15115123, 15612108, 15665113, 15727639...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Body | CID |
|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL | H | 1781 | Pipe To Water Pump | GAS | 4 Cyl 1.8L | Coupe | - |
- Cut to fit
- 90 Degree Molded Heater Hose
- Product Attributes:
- Molded: Yes
- Centerline Length: 254
- End 1 Inside Diameter:
- .625
- 16
- Angle: 90
- Arm Length:
- 102
- 152
- 4
- 6
- Material: Epdm
- End 2 Inside Diameter:
- .625
- 16
- Quick Connect Fitting Quantity: 0
-
Features:
- Resists electrochemical degradation and water permeation
- Use with heater hose connectors and bulk heater hose to create custom assemblies
- Compatible for coolant, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- It can be difficult to find hoses that easily adapt to sharp bends in your assemblies. Gates created a 90 Degree Molded Heater Hose to make replacing hoses with existing sharp bends easy. Conveniently, our 38 sizes handle thousands of applications and are built to last.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0032224, 027004156, 05743507, 06006269, 07HS00043A, 07HS00044A, 0K01315421, 10002473, 10006390, 10018899, 10021318, 10038502, 10060964, 10065741, 10080395, 10135305, 10135333, 10145098...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Body | CID |
|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL | H | 1781 | Pipe-1 To Engine | GAS | 4 Cyl 1.8L | Hatchback | - |
- Cut to Length, 4"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 60
- Weight Per Length: 8.25 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 600
- End 1 Inside Diameter:
- .5
- 13
- Material: Epdm
- End 2 Inside Diameter:
- .5
- 13
-
Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Get more out of your heater hose with Safety Stripe Heater Hose, constructed for extra-long service life. Intended for use on cars and light trucks, this EPDM hose is unaffected by most coolants, non-oil based coolant additives and high cooling system pressures. (Not recommended for heavy-duty trucks, buses, or off-road construction equipment; use Green Stripe heater hose for these applications.)
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
06A121497AA, 06A121497E, 09551D100, 100799100C, 10378155, 12608670, 12787736, 140551FJ0A, 14055EW600, 15077095, 15077147, 15181119, 15257756, 15710551, 15727309, 15763280, 15763290, 15834774...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Body | Aspiration | CID |
|---|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL | H | 1781 | Thermostat To Intake Manifold | GAS | 4 Cyl 1.8L | Coupe | Turbocharged | - |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Subaru GL |
- If possible check the old motors OE # in the X-Ref file. Threaded shaft.
- Motor Only
- A/C & Heater
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Subaru GL-10 |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Subaru GL |
Additional Fitment Information:
| Vehicle |
|---|
| 1988 - Subaru RX |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Aspiration | CID |
|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL-10 | H | 1781 | Throttle Body To Engine | GAS | 4 Cyl 1.8L | Turbocharged | - |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Body | Aspiration | CID |
|---|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL | H | 1781 | Engine To Throttle Body | GAS | 4 Cyl 1.8L | Wagon | Turbocharged | - |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter: .31
- Material: Epdm
- End 2 Inside Diameter: .31
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0935270131600, 10020, 10036781, 12637185, 14001S, 1405557Y12, 14055D4200, 140560B000, 140560B001, 140560S310, 1405610V11, 1405630P21, 1405630P24, 1405630R16, 1405640F04, 1405640F12, 1405653J07, 1405653J09...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | Body | Aspiration | CID |
|---|---|---|---|---|---|---|---|---|
| 1988 - Subaru GL | H | 1781 | Pipe To Engine | GAS | 4 Cyl 1.8L | Coupe | Naturally Aspirated | - |
Showing 1 - 10 of 10 products
Loading...