Image
Product
Price
- Cut to fit
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 124
- 4.9
- End 1 Inside Diameter:
- .75
- 19
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- .75
- 19
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
10020454, 10065590, 10087632, 133643R1, 14-2660-4, 14034345, 14100667, 14211S, 1555179, 1945061, 2001, 2004, 2012, 20618, 22602073, 230572, 23121, 25502711...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1991 - Lincoln Mark VII | V | - | Heater To Pipe-1 | GAS | 8 Cyl 5.0L | 302 |
- W/Auto. Temp. Control; Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter:
- .62
- 16
- Material: Epdm
- End 2 Inside Diameter:
- .75
- 19
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
This Part Fits the Following OEM/Substitute Numbers:
10070, 10080350, 10145080, 10145101, 10284262, 14004S, 18070, 19130282, 1W7H 18K580 AB, 1W7Z 18472 AB, 2714401P00, 64429, 86003, 86006, 86010, 87603, 87918, 96455704...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1991 - Lincoln Continental | V | - | Heater To Valve | GAS | 6 Cyl 3.8L | 232 |
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Town Car |
- When replacing the switch, also replace the O-Ring - N807083S
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Town Car |
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Mark VII |
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Town Car |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- New with Clutch
- 'R12-Refrigerant System'
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Continental |
Additional Fitment Information:
| Vehicle |
|---|
| 1991 - Lincoln Town Car |
- Cut to Length, 6"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 60
- Weight Per Length: 11.70 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 600
- End 1 Inside Diameter:
- .625
- 16
- Material: Epdm
- End 2 Inside Diameter:
- .625
- 16
-
Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Get more out of your heater hose with Safety Stripe Heater Hose, constructed for extra-long service life. Intended for use on cars and light trucks, this EPDM hose is unaffected by most coolants, non-oil based coolant additives and high cooling system pressures. (Not recommended for heavy-duty trucks, buses, or off-road construction equipment; use Green Stripe heater hose for these applications.)
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0K55261B16C, 0K55261B22F, 10023264, 10230417, 10427731, 12322342, 12368235, 12575636, 12600099, 12604941, 12639709, 12639710, 14055JK20A, 15024548, 15051852, 15051853, 15064188, 15064189...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1991 - Lincoln Town Car | V | - | Pipe-1 To Water Pump | GAS | 8 Cyl 4.6L | 281 |
- Cut to fit
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 244
- 9.6
- End 1 Inside Diameter:
- .62
- 16
- Material: Epdm
- End 2 Inside Diameter:
- .75
- 19
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
This Part Fits the Following OEM/Substitute Numbers:
10079, 10145763, 10241617, 12386911, 14005S, 15652879, 15668784, 15781525, 18079, 19129802, 22729506, 63223, 64325, 64425, 8156528790, 86112, 86115, 8724550360...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1991 - Lincoln Continental | V | - | Pipe To Water Pump | GAS | 6 Cyl 3.8L | 232 |
Showing 1 - 10 of 14 products
Loading...