Image
Product
Price
This Part Fits the Following OEM/Substitute Numbers:
10065675, 10135307, 10142, 10188037, 10190667, 14055-31U00, 14056-46R00, 14099017, 14244S, 14592S, 15530513, 18142, 22601689, 22602073, 22610689, 22612883, 22646764, 25525214...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2008 - Hummer H3 | V | 5328 | Pipe To Thermostat | 8 Cyl 5.3L | 325 |
- NEW COMPRESSOR W/ CLUTCH
- DENSO is the OE supplier for this vehicle; OE-specified Oil included.
- New A/C Compressor
- As one of the world’s largest OE suppliers of A/C compressors, DENSO units are specified by most major vehicle manufacturers. DENSO First Time Fit A/C compressors are manufactured and tested to the strictest OE standards for unparalleled performance. At DENSO, we bring together everything we know as an air conditioning systems manufacturer to bring you the highest quality line of factory-new compressors available. When it comes to new compressors, you can't do better than going with a unit manufactured by the OE supplier. At DENSO, we know these units better than anyone because we originally designed them. Our compressors are built to meet DENSO’s unsurpassed reputation for technological superiority. You can relax knowing DENSO will give you the right part and the right fit, the first time.
This Part Fits the Following OEM/Substitute Numbers:
001138, 10000631, 10364873, 12624430, 12647259, 15-20941, 15-21127, 15068854, 15081861, 15100337, 15100338, 15169964, 15169965, 15707611, 1869N, 19130450, 20-21711, 254471...VIEW MORE
Additional Fitment Information:
| Vehicle | Body |
|---|---|
| 2008 - Hummer H2 | Sport Utility |
- New Nippondenso 10S20F Compressor with Clutch
- ; with 10S20F Compressor New with Clutch May Require use of OE Manifold; DeSlugger Recommended to Eliminate Compressor Damage on Vehicles with Low Mount Compressor
- New Nippondenso 10S20F Compressor with Clutch
- New Compressor
- Product Attributes:
- : 4.250
- Compatible Refrigerant Oil Type: Pag 46
- Refrigerant Type: R134a
- Clutch Included: Yes
- New or Reman: New
- Discharge Port Type: Sealing Washer
- Printed Foot Note: May Require Use Of Oe Manifold; Deslugger [36141] Recommended To Eliminate Compressor Damage On Vehicles With Low Mount Compressor
- Suction Port Type: Sealing Washer
- Mounting Hardware?: Not Included
- O-Ring B Number/Desc: [24402] / Slimline Washer
- O-Ring A Number/Desc: [24404] / Slimline Washer
- Pulley Diameter MM: 107.950
- Compressor Type: 10s20f
- Pulley Belt Type: Serpentine
- Pulley Groove Quantity: 4
- Terminal Type: Pin
- Mount Distance MM: 16.510
- Distance From Clutch To Mounting Flange: 0.65625
- Coil Clock Position: Wire Lead
- Mounting Type: Tangent Mount
- Pulley Ridge Diameter: 4.250
- Clutch Maximum Diameter: 4.250
- Pulley Lip Diameter: 4.250
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Body | CID |
|---|---|---|---|---|---|
| 2008 - Hummer H2 | V | 6162 | 8 Cyl 6.2L | Crew Cab Pickup | 376 |
- New Nippondenso 10S20F Compressor with Clutch
- ; with 10S20F Compressor New with Clutch May Require use of OE Manifold; DeSlugger Recommended to Eliminate Compressor Damage on Vehicles with Low Mount Compressor New Part
- New Nippondenso 10S20F Compressor with Clutch
- New Compressor
- Product Attributes:
- : 4.250
- Compatible Refrigerant Oil Type: Pag 46
- Refrigerant Type: R134a
- Clutch Included: Yes
- New or Reman: New
- Discharge Port Type: Sealing Washer
- Printed Foot Note: May Require Use Of Oe Manifold; Deslugger [36141] Recommended To Eliminate Compressor Damage On Vehicles With Low Mount Compressor
- Suction Port Type: Sealing Washer
- Mounting Hardware?: Not Included
- O-Ring B Number/Desc: [24402] / Slimline Washer
- O-Ring A Number/Desc: [24404] / Slimline Washer
- Pulley Diameter MM: 107.950
- Compressor Type: 10s20f
- Pulley Belt Type: Serpentine
- Pulley Groove Quantity: 4
- Terminal Type: Pin
- Mount Distance MM: 16.510
- Distance From Clutch To Mounting Flange: 0.65625
- Coil Clock Position: Wire Lead
- Mounting Type: Tangent Mount
- Pulley Ridge Diameter: 4.250
- Clutch Maximum Diameter: 4.250
- Pulley Lip Diameter: 4.250
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Body | CID |
|---|---|---|---|---|---|
| 2008 - Hummer H2 | V | 6162 | 8 Cyl 6.2L | Sport Utility | 376 |
- New Nippondenso 10S20F Compressor with Clutch
- ; with 10S17F Compressor New with Clutch Replacement of Stretch Fit Belt is Required May Require use of OE Manifold; DeSlugger Recommended to Eliminate Compressor Damage on Vehicles with Low Mount Compressor Replacement of Stretch Fit Belt is Required
- New Nippondenso 10S20F Compressor with Clutch
- New Compressor
- Product Attributes:
- : 4.250
- Compatible Refrigerant Oil Type: Pag 46
- Refrigerant Type: R134a
- Clutch Included: Yes
- New or Reman: New
- Discharge Port Type: Sealing Washer
- Printed Foot Note: May Require Use Of Oe Manifold; Deslugger [36141] Recommended To Eliminate Compressor Damage On Vehicles With Low Mount Compressor
- Suction Port Type: Sealing Washer
- Mounting Hardware?: Not Included
- O-Ring B Number/Desc: [24402] / Slimline Washer
- O-Ring A Number/Desc: [24404] / Slimline Washer
- Pulley Diameter MM: 107.950
- Compressor Type: 10s20f
- Pulley Belt Type: Serpentine
- Pulley Groove Quantity: 4
- Terminal Type: Pin
- Mount Distance MM: 16.510
- Distance From Clutch To Mounting Flange: 0.65625
- Coil Clock Position: Wire Lead
- Mounting Type: Tangent Mount
- Pulley Ridge Diameter: 4.250
- Clutch Maximum Diameter: 4.250
- Pulley Lip Diameter: 4.250
This Part Fits the Following OEM/Substitute Numbers:
031867, 032057, 034279N, 034279ND, 034810N, 034810ND, 035126N, 035126ND, 035127N, 035127ND, 0610081, 10000631, 10364873, 10366545, 11178377, 1420940, 1421127AFT, 1421127NEW...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2008 - Hummer H3 | V | 5328 | 8 Cyl 5.3L | 325 |
- 5/8 In.
- Small I.D. Heater Hose
- Product Attributes:
- Trunk Height: 5 1/2
- End 2 Outside Diameter: 15/16
- Contains Heat Shield: N
- End 1 Inside Diameter: 5/8
- End 1 Outside Diameter: 15/16
- Hose Type: Single I.d. Hose
- SAE Specification: Sae J20r3 Class D-1, Sae J1684 Type Ec
- Contains Protective Sleeve: N
- End 2 Inside Diameter: 5/8
This Part Fits the Following OEM/Substitute Numbers:
10044, 10761, 11535, 14093S, 14518S, 14566S, 18044, 18761, 19535, 79722-SZA-A00, 79722-TK8-A00, 807615081, B87842
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2008 - Hummer H3 | L | 3654 | Pipe To Engine | 5 Cyl 3.7L | 223 |
- Cut to Length, 13"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 50
- Weight Per Length: 13.20 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 50
- 600
- End 1 Inside Diameter:
- .75
- 19
- End 2 Inside Diameter:
- .75
- 19
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
10229491, 12322343, 12368236, 12804554, 15043166, 15043168, 15079924, 15246436, 15282248, 15293037, 15755541, 15758384, 15782202, 1787185Z00, 1787285Z00, 19129880, 19129909, 19129949...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2008 - Hummer H3 | V | 5328 | Heater To Pipe-2 | GAS | 8 Cyl 5.3L | 325 |
- Cut to fit
- 90 Degree Molded Heater Hose
- Product Attributes:
- Molded: Yes
- Centerline Length:
- 10
- 254
- End 1 Inside Diameter:
- .75
- 19
- Arm Length:
- 102
- 152
- 4
- 6
- End 2 Inside Diameter:
- .75
- 19
- Quick Connect Fitting Quantity: 0
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
10017940, 10065640, 10065675, 10120065, 10135307, 10145119, 10188037, 10218423, 10227419, 10385281, 10441374, 1405531U00, 1405646R00, 1405670F05, 14244S, 15077061, 15123654, 15258060...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2008 - Hummer H3 | V | 5328 | Pipe-2 To Thermostat | GAS | 8 Cyl 5.3L | 325 |
- Cut to Length, 33"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 60
- Weight Per Length: 11.70 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 50
- 600
- End 1 Inside Diameter:
- .625
- 16
- End 2 Inside Diameter:
- .625
- 16
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
0K55261B16C, 0K55261B22F, 10023264, 10230417, 10427731, 12322342, 12368235, 12575636, 12600099, 12604941, 12639709, 12639710, 14055JK20A, 15024548, 15051852, 15051853, 15064188, 15064189...VIEW MORE
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2008 - Hummer H2 | V | 6162 | Heater To Thermostat | GAS | 8 Cyl 6.2L | 376 |
- Cut to Length, 13"
- Straight Heater Hose (Standard)
- Product Attributes:
- Molded: No
- Working Pressure: 60
- Weight Per Length: 11.70 Lbs./carton
- Centerline Length:
- 15.24
- 15240
- 50
- 600
- End 1 Inside Diameter:
- .625
- 16
- End 2 Inside Diameter:
- .625
- 16
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 2008 - Hummer H3 | V | 5328 | Heater To Pipe-1 | GAS | 8 Cyl 5.3L | 325 |
Showing 1 - 10 of 45 products
Loading...