Image
Product
Price
- 170 Degrees F 203 Degrees F May Require Hose from the Housing to the Heater Core Replacement OE Specified Temperature ; Includes upper & lower housing, thermostats, and seal
- Thermostat Assembly
This Part Fits the Following OEM/Substitute Numbers:
68003582AB, 86087, 902-319, 9134AT, 9TA4319, CO34760, NI, TA4319, TA4319DL
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2009 - Jeep Patriot | L | 1998 | 4 Cyl 2.0L | 122 |
- Class 3 Trailer Hitch; 2in. Receiver; Select Jeep Compass; Patriot
- 4000lbs. Gross Trailer Weight; 400lbs. Tongue Weight Square Main Body~No Drilling Required~Visibility: Concealed~Install Time 45 Minutes~Temporarily Lower Exhaust For Installation
- CURT 13548 Class 3 Trailer Hitch; 2-Inch Receiver; Fits Select Jeep Compass; Patriot
- Class III 2 in. Receiver Hitch
- Product Attributes:
- Gross Trailer Weight: 4000 Lbs.
- Visibility: Concealed
- Weight Carrying Capacity: 4000
- Body Shape: Square
- Install Time: 45 Minutes
- WC Tongue Weight: 400
- Receiver Tube Size: 2.000 In.
-
Features:
- Made w/A Vehicle-Specific Design For A Custom Fit
- Tested For Safety In Accordance w/SAE J684
- Precisely Welded For Superior Strength And Fit
- Protected By A Durable High-Gloss Black Powder Coat Finish
- Co-Cured In A Rust-Resistant Liquid Bonderite Coating
- Strengthened w/A Cast Welded Seamless Collar
- Equipped w/An Open-Back Receiver For Easy Cleaning
- Backed By A Limited Lifetime Warranty
- Made in USA [may include imported hardware]
- Whatever your task at hand -- whether its launching that boat before daybreak, setting up your camper before the rush or getting a final load to the dump before close -- CURT class 3 trailer hitches offer the strength needed for serious towing. They make it easy to hitch up and Bring It, offering a vehicle-specific fit and the weight capacity to handle a variety of trailers. Custom class 3 hitches are the most common type of receiver hitch for pickup trucks and SUVs. Because of their weight range, they are also found on full-size cars, crossovers and minivans. Each custom-fit class 3 hitch package is made for vehicle-specific mounting. This particular kit fits certain years of the Jeep Compass and Patriot (see application info to verify vehicle compatibility). It provides a weight carrying capacity of 4,000 lbs. GTW and 400 lbs. TW. CURT class 3 trailer hitches are typically used to attach and haul utility trailers, boat trailers, campers, snowmobile or ATV haulers and more (NOTE: Never exceed the lowest-rated towing component). Each class 3 hitch has a 2 in. receiver tube and is tested in accordance with SAE J684 for safety. To ensure that CURT class 3 receiver hitches have what it takes for serious trailering, they are designed using a hands-on approach and are constructed with rugged, high-strength steel and precise welding. We also protect our class 3 hitches in a co-cured finish of liquid Bonderite and black powder coat for superior resistance to rust, chipping and UV damage.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2009 - Jeep Patriot | L | 1998 | Rear | 4 Cyl 2.0L | 122 |
- Non-Greaseable Super Strength Universal Joint
- with 2.188 (in) Inside Lock-Up Non-Greasable Super Strength U-Joint
- MOOG 371 Non-Greaseable Super Strength Universal Joint for Jeep Wrangler
- Product Attributes:
- Bearing Cap Type: 4 Grooved Round Bearings
- U-Joint Identification: 4 Grooved Round Bearings
- Bearing Cap Axis 2 Diameter:
- 1.188
- 30.1
- Grade Type: Premium
- Length Axis 1:
- 2.06
- 52.578
- Length Axis 2:
- 2.06
- 52.578
- Length Measurement B: Inside Of Groove To Inside Of Groove Plus Thickness Of 2 Lock Rings
- Bearing Cap Axis 1 Diameter:
- 1.188
- 30.2
- Greaseable: No
- Part Description: Universal Joint
- Length Measurement A: Outside Of Groove To Outside Of Groove
-
Features:
- BUILT TO LAST -- Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
- CORROSION PROTECTION -- Exclusive MICRO SHIELDâ„¢ coating protects against rust and corrosion
- KEEPS DIRT OUT -- Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE -- Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
This Part Fits the Following OEM/Substitute Numbers:
1-0297, 1-0297BF, 10297, 10297BF, 10297G, 10298, 114-645, 114645, 114645B, 20139, 20193, 20193E, 20193P, 20716, 210-0297, 2100297, 2150297, 2150299...VIEW MORE
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2009 - Jeep Wrangler | Front Axle at Wheels | 4WD |
- with 3.625in Outside Snap Ring Dimension with Aftermarket 1350 Drive Shaft 1.188in Bearing Cap Diameter Non-Greasable with CV Front Driveshaft with Uncoated
- HGVF
- Product Attributes:
- Bearing Cap Type B: Osr
- Length B (mm): 92.1
- SR(2)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Type A: Osr
- Greaseable: N
- Bearing Cap Diameter (2): 1.188
- Bearing Cap Diameter (1): 1.188
- OEM Mfg: Spicer
- OEM Series: 1350/spl30
- Bearing Cap Diameter B (mm): 1.188
- Snap Ring Included: Y
- Snap Ring Type: External
- Length A (mm): 92.1
- SR(1)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Diameter A (mm): 1.188
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2009 - Jeep Wrangler | Rear Driveshaft at Rear Axle | 4WD |
- with 3.625in Outside Snap Ring Dimension with Aftermarket 1350 Drive Shaft 1.188in Bearing Cap Diameter Non-Greasable with CV Front Driveshaft with Uncoated
- HGVF
- Product Attributes:
- Bearing Cap Type B: Osr
- Length B (mm): 92.1
- SR(2)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Type A: Osr
- Greaseable: N
- Bearing Cap Diameter (2): 1.188
- Bearing Cap Diameter (1): 1.188
- OEM Mfg: Spicer
- OEM Series: 1350/spl30
- Bearing Cap Diameter B (mm): 1.188
- Snap Ring Included: Y
- Snap Ring Type: External
- Length A (mm): 92.1
- SR(1)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Diameter A (mm): 1.188
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2009 - Jeep Wrangler | Front Driveshaft - CV at Transfer Case | 4WD |
- with 3.625in Outside Snap Ring Dimension with Aftermarket 1350 Drive Shaft 1.188in Bearing Cap Diameter Non-Greasable with CV Front Driveshaft with Uncoated
- HGVF
- Product Attributes:
- Bearing Cap Type B: Osr
- Length B (mm): 92.1
- SR(2)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Type A: Osr
- Greaseable: N
- Bearing Cap Diameter (2): 1.188
- Bearing Cap Diameter (1): 1.188
- OEM Mfg: Spicer
- OEM Series: 1350/spl30
- Bearing Cap Diameter B (mm): 1.188
- Snap Ring Included: Y
- Snap Ring Type: External
- Length A (mm): 92.1
- SR(1)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Diameter A (mm): 1.188
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2009 - Jeep Wrangler | Rear Driveshaft at Transmission | 4WD |
- Universal Joint
- with CV Front Driveshaft with Uncoated 1.188in Bearing Cap Diameter Non-Greasable with 3.625in Outside Snap Ring Dimension with Aftermarket 1350 Drive Shaft
- HGVF
- Product Attributes:
- Bearing Cap Type B: Osr
- Snap Ring (1): 3.625
- Snap Ring (2): 3.625
- Length B (mm): 92.1
- SR(2)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Type A: Osr
- Greaseable: N
- Bearing Cap Diameter (2): 1.188
- Bearing Cap Diameter (1): 1.188
- OEM Mfg: Spicer
- OEM Series: 1350/spl30
- Bearing Cap Diameter B (mm): 1.188
- Snap Ring Included: Y
- Snap Ring Type: External
- Length A (mm): 92.1
- SR(1)Brng Cap to Brng Cap(OSR): 3.625
- Bearing Cap Diameter A (mm): 1.188
- You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
-
Suggested Purchase Quantity: 4
- Most jobs typically require 4 of this item.
This Part Fits the Following OEM/Substitute Numbers:
15-178X, 2-0052, 2-0053, 2-0053G, 2-0053P, 2-0799, 231, 232, 331, 331BL, 45U0103, 45U0109, 45U0123, 5-178X, UJ231, UJ232, UJ331, UJ331BL...VIEW MORE
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2009 - Jeep Wrangler | Front Driveshaft - CV at Transfer Case | 4WD |
- Black Steel Grille Guard; Select Jeep Wrangler JK
- 1 pc.; Semi-Gloss Black Powder Coat; Carbon Steel; w/o Headlight Cage; Includes Hardware
- ARIES 1050 1-1/2-Inch Black Steel Grille Guard; No-Drill; Select Jeep Wrangler JK
- Grille Guard
- Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
-
Features:
- One-Piece/ 1-1/2 in. Diameter/ Heavy-Wall Tube Design
- High-Strength Carbon Steel Construction
- Dual-Layer E-Coat And Black Powder Coat Finish
- Two Pre-Drilled Holes In The Crossbar For Mounting LED Light Bars
- Vertical Rubber Stripping To Help Maintain Clean Finish
- No-Drill/ Vehicle-Specific Application For Custom Fit
- Includes Grille Guard And Mounting Hardware
- Grille Guard May Interfere w/Forward-Facing Cameras Or Sensors
- For the conqueror in every truck, Jeep or SUV owner, the ARIES grille guard offers the tough, trail-ready look you demand. It begins with a one-piece frame of 1/4 in. thick welded plates and 1-1/2 in. mandrel-bent tubing for a solid build. Each one is made with a vehicle-specific design for a better fit, easier install and more secure mounting. The side brush guards are custom-bent to contour to the profile of your vehicle, while the mounting brackets are positioned for a no-drill application. This means pre-existing factory holes are used to ensure optimum fitment and less vibration. This particular custom grille guard fits specific years of the Jeep Wrangler (see application info to verify). The ARIES grille guard also makes it easy to customize the look of your vehicle. Not only does the crossbar have two pre-drilled holes for mounting aftermarket LED lights, but many of our grille guards are also available in two finish options -- polished stainless steel or semi-gloss black steel. The stainless steel grille guard is made with 304 stainless, being high in nickel content and truly resistant to rust and corrosion. This option comes with a mirror-like polished finish for a definitive shine. The semi-gloss black grille guard is made with high-strength carbon steel for added strength. It features a tough, dual-layer E-coat and black powder coat finish to protect against rust, scratches and the elements. All ARIES grille guards also come with rubber stripping along the risers to protect the frame against scuffs and scratches.
Additional Fitment Information:
| Vehicle |
|---|
| 2009 - Jeep Wrangler |
- Dual-Output 7/4-Way Connector with Backup Alarm (Plugs into USCAR)
- w/Back Up Alarm; GM/Ford Plug For Models w/Factory Tow Package
- CURT 57101 Dual-Output Vehicle-Side 7-Pin; 4-Pin Connectors with Backup Alarm; Factory Tow Package and USCAR Socket Required
- 7-Way Round RV To 4-Way Flat Adapter
-
Features:
- Plugs Into Round Uscar Socket On Ford Or Gm
- Replaces The Factory-Equipped 7-Way Socket
- Integrated Backup Alarm Sounds When Vehicle Is In Reverse
- Simple Plug-And-Play Design Eliminates The Need For Splicing
- 4-Way Flat Connects Tail Lights Brake Lights And Turn Signals
- 7-Way Rave Blade Adds Reverse Lights Electric Brakes
- Dust Covers Included To Keep Connectors Clean When Not In Use
- Bracket Securely Mounts Wiring To The Vehicle Or Trailer Hitch
- A CURT custom original equipment vehicle-to-trailer connector (sometimes called a T-connector) is a simple, plug-and-play electrical device that eliminates the need for cutting, splicing and soldering when installing vehicle-to-trailer wiring. Most vehicles do not come ready to tow. Unless your vehicle has a towing package, it is probably not equipped with a trailer wiring connector. This is where CURTs OE vehicle-to-trailer connectors come into play. A custom wiring connector uses a single original equipment plug to plug into a special socket provided by your vehicle. Though this option is not available on every vehicle, some automotive manufacturers design their vehicles to be easily equipped for towing by supplying a socket, integrated into the vehicles electrical system, to readily accept a custom wiring connector. With a CURT custom OE connector, there is no need to tap into the taillight assembly because a special socket is already provided. This special custom vehicle-to-trailer wiring connector provides a multi-function connector socket. It is designed to plug into a circular 7-prong OEM socket and replace a factory-equipped 7-way connector with a 7-way RV blade and 4-way flat. It specifically offers a custom wiring option for a variety of vehicles (see application info to verify fitment with your vehicle).This multipurpose socket comes with its own backup alarm, a mounting bracket and all necessary mounting hardware for a complete installation. CURT custom vehicle-to-trailer wiring connectors are designed to be long-lasting and simple to install. They come with dust covers to keep your connector clean when not in use.
Additional Fitment Information:
| Vehicle | Sub Model |
|---|---|
| 2009 - Jeep Wrangler | Sahara |
- Replaces H5687
- Raybestos R-Line
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
084-1772, 117.61038, 30044307AQ, 30044307W, 5682, F139839, H5661, H5682, H5682Q, H5687AT, H5988, H6061, HW5682
Additional Fitment Information:
| Vehicle | Position | Rear Brake | Sub Model |
|---|---|---|---|
| 2009 - Jeep Grand Cherokee | Rear | Disc | Overland |
Showing 1 - 10 of 28 products
Loading...