Image
Product
Price
- Ignition Switch;
- Ignition Switch
-
Features:
- Ignition Switch
- Crown Automotive is the premiere manufacturer and distributor of quality replacement parts for Jeep(R) CJ(TM), Wrangler(TM), Cherokee(TM), Grand Cherokee(TM), Liberty(TM), and Commander(TM). With over 8,000 different parts in stock for Jeep(R) vehicles from 1942 on up, Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory-discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission and transfer case components. Crown Automotive also offers an exclusive line of component kits and accessory products. Because we know that Jeeps are driven harder than most other vehicles, we emphasize offering only quality parts. In fact, we test parts on Jeeps before distributing them to our dealers to insure that they meet our standards for quality. Crown also supports its entire line with a 12 month/12,000 mile warranty to insure our dealers and their customers of our commitment to offering quality parts.
Additional Fitment Information:
| Vehicle |
|---|
| 1974 - Jeep CJ6 |
- HEI In-Cap Design; Primary Resist 0.5 Ohms; Secondary 8.6 k Ohms; Turn Ratio 80:1; Max Voltage 45000V; Red And Yellow Primary Wire; Gray;CARB E.O. D-221-6
- SuperCoil Ignition Coil; HEI In-Cap Design; Primary Resist 0.5 Ohms; Secondary 8.6 k Ohms; Turn Ratio 80:1; Max Voltage 45000V; Red And Yellow Primary Wire; Gray;
- SuperCoil Ignition Coil
- Product Attributes:
- Peak Increase in Voltage: 18%
- WARNING CA Proposition 65: Yes
- Turns Ratio: 80:1
- Maximum Voltage: 45000
- Primary Resistance: .500 Ohms
- Secondary Resistance: 8.6k Ohms
-
Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-31
- MSD 8225
- Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.
Additional Fitment Information:
| Vehicle |
|---|
| 1974 - Chevrolet Laguna |
- High Performance; w/MSD 6 Series; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37 0.7 OHMs Primary Resistance/4.5K OHMs Secondary Resistance
- Blaster 2 Ignition Coil; High Performance; w/MSD 6 Series; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- Available In Red And Black
- Our famous red canister coil! Great choice with an MSD 6-series ignition. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister. The Blaster Coil is designed to mount in most factory canister coil mounts. MSD also offers a Chrome Coil Bracket, PN 8213. It is recommended to mount the PN 8202, PN 82023, and 8223 coils in an upright position. The High Vibration Coil, PN 8222, can be mounted in any position due to its epoxy potting compound.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1974 - Chevrolet Camaro | L | - | 6 Cyl 4.1L | 250 |
- High Performance; w/MSD 6 Series; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37 0.7 OHMs Primary Resistance/4.5K OHMs Secondary Resistance
- Blaster 2 Ignition Coil; High Performance; w/MSD 6 Series; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- Available In Red And Black
- Our famous red canister coil! Great choice with an MSD 6-series ignition. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister. The Blaster Coil is designed to mount in most factory canister coil mounts. MSD also offers a Chrome Coil Bracket, PN 8213. It is recommended to mount the PN 8202, PN 82023, and 8223 coils in an upright position. The High Vibration Coil, PN 8222, can be mounted in any position due to its epoxy potting compound.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine VIN | CID |
|---|---|---|---|---|---|
| 1974 - Chevrolet Caprice | V | - | 8 Cyl 5.7L | H | 350 |
- Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37
- Blaster 2 Ignition Coil; Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for stock points or electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Supplied w/2 Spark Plug Wire Boots/Terminals/Ballast Resistor
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- This Blaster Coil is supplied with a ballast resistor. If your application uses a points distributor, the ballast must be used. Late-model electronic ignitions or an MSD Ignition do not require the ballast. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1974 - Ford Bronco | L | 3278 | 6 Cyl 3.3L | 200 |
- Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37
- Blaster 2 Ignition Coil; Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for stock points or electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Supplied w/2 Spark Plug Wire Boots/Terminals/Ballast Resistor
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- This Blaster Coil is supplied with a ballast resistor. If your application uses a points distributor, the ballast must be used. Late-model electronic ignitions or an MSD Ignition do not require the ballast. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1974 - Ford LTD | V | 5753 | 8 Cyl 5.8L | Windsor | 351 |
- Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37
- Blaster 2 Ignition Coil; Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for stock points or electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Supplied w/2 Spark Plug Wire Boots/Terminals/Ballast Resistor
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- This Blaster Coil is supplied with a ballast resistor. If your application uses a points distributor, the ballast must be used. Late-model electronic ignitions or an MSD Ignition do not require the ballast. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1974 - Ford Bronco | L | 3278 | 6 Cyl 3.3L | 200 |
- Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;CARB E.O. D-40-37
- Blaster 2 Ignition Coil; Includes Ballast Resistor For Stock Applications; 8 mH Inductance; 45000 Max Volts; 140mA Peak Current; 350 uS Spark Duration; 100:1 Turns Ratio; Red;
- Blaster 2 Ignition Coil
- Product Attributes:
- Spark Duration: 350 Us
- Turns Ratio: 100:1
- Inductance: 8 Mh
- Maximum Voltage: 45000
- Peak Current: 140 Ma
- Primary Resistance: .700 Ohms
- Secondary Resistance: 4.5k Ohms
-
Features:
- Improved output coil for stock points or electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Supplied w/2 Spark Plug Wire Boots/Terminals/Ballast Resistor
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Metal Canister Is Filled w/Premium Grade Oil For Cooling
- CARB E.O. Approved
- This Blaster Coil is supplied with a ballast resistor. If your application uses a points distributor, the ballast must be used. Late-model electronic ignitions or an MSD Ignition do not require the ballast. If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD Blaster Ignition, MSD 5, 6, or 7, the Blaster Coil line is the right choice. Our Blaster Coils are designed for improved spark output! Special 100:1 windings are used to provide maximum build-up of voltage! These windings are held secure and kept cool in an oil-filled metal canister.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1974 - Ford LTD | V | 5753 | 8 Cyl 5.8L | Windsor | 351 |
- 12 Volt C.A.R.B. E.O. D-57-22 Changes Std. Point-Type Distributor to High Output, Hall Effect Triggered Electronic Ignition IGNITOR Series Legal in all 50 States and Canada with Bosch 009 or 050 Distributor
Additional Fitment Information:
| Vehicle |
|---|
| 1974 - Volkswagen Transporter |
- HEI In-Cap Design; Primary Resist 0.5 Ohms; Secondary 8.6 k Ohms; Turn Ratio 80:1; Max Voltage 45000V; Red And White Primary Wire;CARB E.O. D-221-6
- SuperCoil Ignition Coil; HEI In-Cap Design; Primary Resist 0.5 Ohms; Secondary 8.6 k Ohms; Turn Ratio 80:1; Max Voltage 45000V; Red And White Primary Wire;
- SuperCoil Ignition Coil
- Product Attributes:
- WARNING CA Proposition 65: Yes
-
Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-32
- Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.
Additional Fitment Information:
| Vehicle |
|---|
| 1974 - Buick Regal |
Showing 1 - 10 of 131 products
Loading...