Image
Product
Price
- Standard Grade Universal Catalytic Converter - 2.25in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.25in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Angled
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 5.125
- Body Height: 3.5
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.25
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 91075 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Aspiration | CID |
|---|---|---|---|---|---|---|
| 1995 - Toyota Supra | L | 2997 | Rear | 6 Cyl 3.0L | Naturally Aspirated | - |
- HM Grade Direct-Fit Catalytic Converter
- Magnaflow HM Grade Direct-Fit Catalytic Converter
- Direct-Fit HM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: Yes
- Tube Material: Stainless Steel
- Outlet Gasket Included: Yes
- Grade Type: Regular
- Hangers Included: No
- Heat Shield Attached: No
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Spun
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 0
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- Keep the check engine light off with MagnaFlow HM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 50801. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 1992-1996 Toyota Camry and interchanges with OE parts 25508-74150 and 25508-74190. Avoid potential exhaust leaks by using the included gaskets to get a proper seal. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
25508-74150, 25508-74190, 2550874150, 2550874190
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1995 - Toyota Camry | L | 2164 | Front | 4 Cyl 2.2L | - |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.375
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 53004 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1995 - Toyota Pickup | V | 2959 | 6 Cyl 3.0L | - |
- Standard Grade Universal Catalytic Converter - 2.00in.
- Cutting and Welding Required
- Magnaflow Standard Grade Universal Catalytic Converter - 2.00in.
- Universal Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 5.5
- Body Height: 3.75
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Outlet Inside Diameter: 2
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Universal Catalytic Converter 91004 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 1995 - Toyota MR2 | L | 2164 | Rear | 4 Cyl 2.2L | - |
- OEM Grade Universal Catalytic Converter - 2.25in.
- Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.25in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.25
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51205 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1995 - Toyota Camry | V | 2995 | 6 Cyl 3.0L | - |
- HM Grade Direct-Fit Catalytic Converter
- Magnaflow HM Grade Direct-Fit Catalytic Converter
- Direct-Fit HM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: Yes
- Tube Material: Stainless Steel
- Oxygen Sensor Location: Post Converter
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: Yes
- Heat Shield Attached: Yes
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: Yes
- Sensor Port Count: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- Torca AccuSeal® Exhaust Clamps provide a full 360-degree equally distributed clamping force preventing pipe distortion while creating a complete seal and maintaining serviceability
- OE-sized barbed exhaust hangers made from corrosion-resistant 410 stainless steel, designed to reduce noise and vibration
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow HM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 23898 helps keep the check engine light off. DIY installation is easy with the proper tools (no cutting or welding required). With features including mandrel-bent tubing to eliminate flow restrictions and stainless steel construction to resist corrosion, you can have confidence in the quality of this catalytic converter. Using state-of-the-art 3D scanning systems in the design process, the MagnaFlow metrology department ensures this new part to fit and function like the original equipment. Designed to fit the 1995-1998 Toyota Tercel and 1996-1998 Toyota Paseo, this direct-fit catalytic converter also interchanges with OE parts 17410-11690 and 17410-11700. The included gaskets & hardware reduce the possibility of a leaking seal while avoiding the need to reuse corroded factory parts for installation. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
17410-11690, 17410-11700, 1741011690, 1741011700
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1995 - Toyota Tercel | L | 1497 | 4 Cyl 1.5L | - |
- OEM Grade Universal Catalytic Converter - 2.25in.
- Cutting and Welding Required
- Magnaflow OEM Grade Universal Catalytic Converter - 2.25in.
- Universal OEM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Outlet Mounting Hardware Included: No
- Body Width: 4.25
- Body Height: 4.375
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Heat Shield Attached: Yes
- Hangers Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter: 2.25
- Substrate Material: Ceramic
- Outlet Orientation: Straight
- Inlet Quantity: 1
- Body Shape: Round
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 0
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 51205 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Aspiration | CID |
|---|---|---|---|---|---|---|
| 1995 - Toyota Previa | L | 2438 | Front | 4 Cyl 2.4L | Supercharged | - |
- HM Grade Direct-Fit Catalytic Converter
- Magnaflow HM Grade Direct-Fit Catalytic Converter
- Direct-Fit HM Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: Yes
- Tube Material: Stainless Steel
- Outlet Gasket Included: Yes
- Grade Type: Regular
- Hangers Included: Yes
- Heat Shield Attached: Yes
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 0
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Precision stamped collector design for optimal exhaust flow, engine efficiency, and fuel economy
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- OE-sized barbed exhaust hangers made from corrosion-resistant 410 stainless steel, designed to reduce noise and vibration
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow HM Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 23897 helps keep the check engine light off. DIY installation is easy with the proper tools (no cutting or welding required). With features including mandrel-bent tubing to eliminate flow restrictions and stainless steel construction to resist corrosion, you can have confidence in the quality of this catalytic converter. Using state-of-the-art 3D scanning systems in the design process, the MagnaFlow metrology department ensures this new part to fit and function like the original equipment. This direct-fit catalytic converter is designed specifically for the 1994-1997 Toyota Previa and interchanges with OE parts 17410-76132 and 17410-76130, among others. The included gaskets & hardware reduce the possibility of a leaking seal while avoiding the need to reuse corroded factory parts for installation. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with Federal/EPA Emission systems.
This Part Fits the Following OEM/Substitute Numbers:
17410-76012, 17410-76130, 17410-76131, 17410-76132, 1741076132
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | Aspiration | CID |
|---|---|---|---|---|---|---|
| 1995 - Toyota Previa | L | 2438 | Front | 4 Cyl 2.4L | Supercharged | - |
- Standard Grade Direct-Fit Catalytic Converter
- Magnaflow Standard Grade Direct-Fit Catalytic Converter
- Direct-Fit Standard Grade Federal (Not legal for sale or use in CA, CO and NY)
- Product Attributes:
- Air Tube Count: 0
- Inlet Gasket Included: Yes
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Grade Type: Regular
- Hangers Included: No
- Heat Shield Attached: Yes
- Outlet Mounting Hardware Included: No
- CARB Executive Order Number: Not Applicable
- Body Type: Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Mounting Hardware Included: No
- Body Material: Stainless Steel
- Substrate Material: Ceramic
- Clamps Included: No
- Sensor Port Count: 0
- Air Tube Adaptable: No
- California Air Resources Board (CARB) Certified: No
-
Features:
- Expertly crafted to replicate OEM-like flow dynamics, maintaining factory performance and fuel efficiency
- Simplifies installation with essential gaskets and hardware being included in the box
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- Precision stamped collector design for optimal exhaust flow, engine efficiency, and fuel economy
- Mandrel bent tubing retains OEM-like design and geometry, ensuring smooth exhaust flow for peak fuel economy and engine operation
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow Standard Grade Federal/EPA Compliant Direct-Fit Catalytic Converter 23896 helps keep the check engine light off. DIY installation is easy with the proper tools (no cutting or welding required). With features including mandrel-bent tubing to eliminate flow restrictions and stainless steel construction to resist corrosion, you can have confidence in the quality of this catalytic converter. Using state-of-the-art 3D scanning systems in the design process, the MagnaFlow metrology department ensures this new part to fit and function like the original equipment. This direct-fit catalytic converter is designed specifically for the 1991-1995 Toyota Previa and interchanges with OE parts 17410-76012 and 17410-76011. The included gaskets & hardware reduce the possibility of a leaking seal while avoiding the need to reuse corroded factory parts for installation. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for pre-OBDII Federally registered vehicles.
This Part Fits the Following OEM/Substitute Numbers:
17410-76011, 17410-76012, 1741076012
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Aspiration | CID |
|---|---|---|---|---|---|
| 1995 - Toyota Previa | L | 2438 | 4 Cyl 2.4L | Naturally Aspirated | - |
- OEM Grade Universal Catalytic Converter - 2.25in.
- Standard Series; 2.25in. Tubing; 2.25in. In/Out; Overall L-13in.; W-5.5in.; Conv L-9in.; NotAirTubeKitAdapt;Not Legal For Sale Or Use On Vehicles Registered In California
- Magnaflow OEM Grade Universal Catalytic Converter - 2.25in.
- 91000 Series Single Sensor OBDII Compliant Universal Cat Converter
- Product Attributes:
- Inlet Orientation: Straight
- Air Tube Count: 0
- Tube Material: Stainless Steel
- Outlet Gasket Included: No
- Inlet Diameter: 2.250 In.
- WARNING CA Proposition 65: No
- Outlet Mounting Hardware Included: No
- Body Width:
- 5.5
- 5.500 In.
- Outlet Attachment Type: Weld-on
- Body Height: 3.75
- Inlet Mounting Hardware Included: No
- Recommended Use: Converter
- Body Material: Stainless Steel
- Clamps Included: No
- Outlet Quantity: 1
- Heat Shield Included: Yes
- Air Tube Adaptable: No
- California Air Resources Board (CARB): No
- Catalytic Converter Format: Pre-catalytic Converter And Main Catalytic Converter
- California Air Resources Board (CARB) Certified: No
- Inlet Gasket Included: No
- Oxygen Sensor Location: Post Converter
- Hangers Included: No
- Heat Shield Attached: Yes
- CARB Executive Order Number: Not Applicable
- Subtitles: Federal / Epa Compliant
- Body Type:
- Clam Shell
- Clam-shell
- Heat Shield Material: Aluminized Steel
- Inlet Inside Diameter:
- 2.25
- 2.250 In.
- Outlet Outside Diameter: 2.250 In.
- Substrate Material: Ceramic
- Main Piping Diameter: 2.250 In.
- Converter Body Size: Oem
- Outlet Orientation: Straight
- Catalytic Converter Air Tube Adapter: Not Air Tube Kit Adaptable
- Inlet Quantity: 1
- Core Substrate Material: Ceramic
- Outlet Inside Diameter: 2.25
- Sensor Port Count: 1
- Emission: Non-california (49-state)
- Inlet Attachment Type: Weld-on
-
Features:
- Expertly formulated catalyst blend maximizes efficiency, ensuring optimal emissions control to keep your check engine light off
- Compact, lightweight construction enables installation in confined areas, welding is required
- Your trusted source for EPA-compliant catalytic converters, providing assurance of genuine compliance while delivering quality that will last
- High strength 16 gauge 409 stainless steel tubing for exceptional corrosion resistance and maximum service life
- Durable 308 stainless steel MIG welds
- MagnaFlow OEM Grade Federal/EPA Compliant Universal Catalytic Converter 91035 helps keep the check engine light off. Get the right fit for a wide array of vehicles thanks to the adaptable Universal design (cutting and welding is required). With highly corrosion resistant, stainless steel construction, you can have confidence in the quality of this catalytic converter. This replacement part is designed to meet or exceed Federal emissions requirements set forth by the EPA, complying with legal standards for OBDII Federally registered vehicles with California or Federal/EPA Emission systems.
Additional Fitment Information:
| Vehicle | Position | Engine Designation | Sub Model | Engine VIN | Aspiration |
|---|---|---|---|---|---|
| 1995 - Toyota Supra | Rear | 2JZ-GE | Base | J | Naturally Aspirated |
Showing 1 - 10 of 25 products
Loading...