2016 Ford BD Diesel Parts
Choose a Model for your 2016 Ford
Image
Product
Price
- BD E-PAS Positive Air Shut-Off 6.7L Powerstroke Ford 2011-2019
- Plug-In Install;
- BD E-PAS Positive Air Shut-Off 6.7L Powerstroke Ford 2011-2019 F250/F350/F450/F550
- Electronic Positive Air Shutdown
- Product Attributes:
- Category: Electronic Emergency Engine Shutdown
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1057932
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Emergency Engine Shutdown
- Easily removed for truck lease returns
- Over speed shut down control utilizing built in Intake Air control valve
- Safely shuts your engine down if over speeding
- Can be installed in less than 1.5 hours
- Factory plug in connections and wiring harness
- Save 3 hours installation labor over mechanical systems
- Does not set ECM Trouble codes
- Automatically resets after shut down
- Only the switch needs a tool to install
- Like a fire extinguisher in your house, or an earthquake kit, it's always better to be prepared. Although rare, Diesel Engine Runaway is caused when external hydrocarbons are drawn into the engine and can cause over speeding and catastrophic engine failure. Life, limb and your vehicle are put in jeopardy. BD Diesel Performance has you covered should the worst happen with our Electronic Positive Air Shutdown (E-PAS) units by cutting the intake air supply to the cylinders and safely shutting down the engine. The E-PAS controls the electronic throttle body in the intake manifold found on most late model diesel engines by closing it to shut off the air supply in emergency situations. The E-PAS can be easily installed in less than 1.5 hours with factory plug-in connectors and premade wiring harnesses. Automatically resets itself after shutdown and can be easily removed for truck lease returns.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD Track Bar Bracket Ford F-250/F-350 SuperDuty 4wd 2008-2022
- 4wd; Lowers track bar mounting point by 2-inches;
- BD Track Bar Bracket Ford F-250/F-350 Superduty 4wd 2008-2022 (Gas & Diesel)
- Track Bar Bracket
- Product Attributes:
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1032110
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Ideal for 2-inch or 2.5-inch levelling kits
- Lowers track bar mounting point by 2-inches
- Corrects steering geometry on lifted vehicles
- Improves bump steer in levelled trucks
- High strength cast iron with ADI heat treat process for maximum strength
- Can be combined with BD 1032110/1032111 Track Bars for adjustability or larger lift height
- Common leveling and lift kits pull the trackbar out of position, affecting ride and steering quality, as well as axle position with respect to the body and frame. BD's track bar bracket relocates the pivot point 2-inch down lower down, offsetting the effect of the lift kit by bringing the trackbar assembly down into the factory position and fixing common steering and tracking issues. The BD track bar bracket is designed with high strength, ADI heat-treated cast iron for maximum strength and provides a strong reliable upgrade.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019
- CARB EO D-553-17; Includes longer studs and spacers plus all gaskets;
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019 F250/F350/F450/F550 Super Duty
- Exhaust Manifold Drivers Side
- Product Attributes:
- Category: Manifolds
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1045804
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Exhaust ports are gasket matched
- High temperature POR 15 black coated
- Includes 16 studs and spacers for BD Scorpion Kits
- Includes exhaust manifold and cross over tube gaskets
- Perfect for BD Scorpion Turbo Kit
- High-silicon ductile cast iron
- 75% thicker walls retain heat and prevents warping
- Machined thicker bolting flange
- 50 state legal
- Includes the longest stud and spacer kit that fits across all 8-cylinders
- Longer exhaust studs improve thermal durability
- Thick spacers are black oxide coated
- Designed using computation fluid dynamics
- BD focused on solving one of the Ford 6.7L common failures, the exhaust manifolds. Crafted with a heavy duty 0.275" thick-walled Hi-Silicon ductile casting, this makes these manifolds 75% thicker to combat cracking due to high exhaust temperatures. Thermal durability has been improved with longer exhaust studs and spacers plus thicker, more durable machined bolting flanges. Fully EGR compatible, BD's exhaust manifold set is the perfect replacement for reliability and peace of mind.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD Injector Line Set Ford 6.7L Power Stroke 2011-2021
- BD Injector Line Set Ford 6.7L Power Stroke 2011-2021 F-250/F-350/F-450
- Injector Line Set
- Product Attributes:
- Category: Lift Pumps & Fuel Supply
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1045825
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Includes full set of hold-down bolts
- OEM quality
- Corrosion resistant
- Exact fit (no adjustment needed by end user)
- No need for adjusting and bending fuel lines
- Preformed to the correct factory specifications
- Stock replacement fuel injector feed lines for Ford 6.7L Power Stroke engines. Replaces OE Part #: BC3Z-9229-A, BC3Z-9229-B
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD 6.7L Power Stroke Exhaust Manifold Passenger Side - Ford 2011-2014
- Cab and Chassis only; Includes longer studs and spacers plus all gaskets;
- BD 6.7L Power Stroke Exhaust Manifold Passenger Side - Ford 2011-2014 F250 / F350 / F450 Pick-up & 2011-2016 F350 / F450 / F550 Cab-Chassis
- Exhaust Manifold Passenger Side
- Product Attributes:
- Category: Manifolds
- Engine: 6.7l Powerstroke 11-16
- Suggested Product: 1043007
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- 50 state legal
- Thick spacers are black oxide coated
- Designed using computation fluid dynamics
- High temperature POR 15 black coated
- Passenger Side
- Gaskets included: exhaust manifold, cross over tube, EGR port
- Fully EGR compatible
- High-silicon ductile cast iron
- 75% thicker walls retain heat and prevents warping
- Machined thicker bolting flange
- Includes the longest stud and spacer kit that fits across all 8-cylinders
- Longer exhaust studs improve thermal durability
- BD focused on solving one of the Ford 6.7L common failures, the exhaust manifolds. Crafted with a heavy duty 0.275" thick-walled Hi-Silicon ductile casting, this makes these manifolds 75% thicker to combat cracking due to high exhaust temperatures. Thermal durability has been improved with longer exhaust studs and spacers plus thicker, more durable machined bolting flanges. Fully EGR compatible, BD's exhaust manifold set is the perfect replacement for reliability and peace of mind.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD 6.7L Power Stroke Screamer Turbo - Ford 2015-2016 F250/F350 Pick-Up
- BD 6.7L Power Stroke Screamer 64mm Turbo - Ford 2015-2016 F-250/F-350 Pick-Up
- Screamer Turbo
- Product Attributes:
- Category: Performance Kits
- Engine: 6.7l Powerstroke 11-16
- Suggested Product: 1043008
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- 64.0mm Billet compressor wheel
- Up to 81lb/min of airflow
- VSR high speed balanced
- Includes updated pedestal and coolant tube for a drop-in install
- Built using a brand new Garrett Turbo
- Custom mixed flow turbine (MFT) wheel with a large 65mm exducer
- Drop-in stock-appearing turbo
- Increased airflow without compromising on low end drivability
- Large 65mm 'mixed flow' turbine wheel increases turbine flow and retains efficiency
- More boost, lower drive pressure, and lower EGT's
- No tuning required and does not set engine codes
- The drop-in, stock-appearing Screamer turbo for the later model Ford 6.7L Powerstroke utilizes modern turbo technology that delivers increased airflow without compromising on low end response. Boost pressure can be increased to improve horsepower potential. The Powerstroke Screamer turbo works with any "box" tuner and further improvements achieved with custom tuning. Drop-in turbo includes the updated 2017-2019 pedestal, coolant line and gaskets for a drop-in replacement on your 2015-2016 vehicle.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD 6.7L Powerstroke 6R140 Flexplate - Ford 2011-2019 w/6-bolt converter
- 6R140 transmission;
- BD 6.7L Powerstroke 6R140 Flexplate - Ford 2011-2019 with6-bolt converter
- Flex-Plate
- Product Attributes:
- Category: Flex Plates
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1061830
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Balanced to OE specifications
- One piece billet machined with integrated counterweight
- Manufactured from Quench and Tempered Steel with a Yield strength of 100,000psi
- Black oxide coated
- Heat treated and hardened ring gear to last longer
- Fits OEM and aftermarket 6-bolt torque converters
- BD's 6r140 Flex Plate is CNC machined out of 1.5x thicker than stock quench and tempered 100,000psi steel. In-house machining incorporates an integrated counterweight which is then balanced to tighter tolerances than OE specifications. Black Oxide coated to resist corrosion. These units will fit any OEM or aftermarket torque converter and affordable enough to upgrade during a converter or transmission swap. The BD Flex Plate is a direct, bolt-in replacement for the stock unit. Great for racing, towing or stock use.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD TowMaster Ford 6R140 Transmission & Converter Package 2011-16 6.7L Power Stroke
- Ford scanner required to update the TCM with the new solenoid code and initiate a relearn - very critical; Early 2011 model years will require 6 bolt flexplate (Approx. Pre Jan 2012 build date), see BD #1041245 or contact Ford;
- BD TowMaster Ford 6R140 Transmission & Converter Package - 2011-2016 6.7L Power Stroke 2wd/4wd
- Trasmission & Converter Package
- Product Attributes:
- Category: Auto Trans & Converter Packages
- Engine: 6.7l Powerstroke 11-16
- Suggested Product: 1032110
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- TRANSMISSION:
- Great for street and towing applications
- Dual surface clutch assembly
- More clutches compared to stock and competitors
- Machined steel reaction ring replaces flexible factory stamping
- Furnace-brazed pump and turbine fins
- Fully remanufactured for long service life
- Custom BD patented pressure plates increase clutch count without sacrificing part strength
- Clutch Count: FORWARD 6 (20% increase over stock)
- Clutch Count: DIRECT 6 (20% increase over stock)
- Clutch Count: INTERMEDIATE 8 (60% increase over stock)
- Electronic Line Pressure Controller for up to 300psi Line Pressure
- Clutch Count: OVERDRIVE 8 (14% increase over stock)
- Clutch Count: LOW REVERSE 5
- Brand new valve body
- PRESSURE CONTROLLER:
- 76% more clutch holding power
- Delivers up to 300psi line pressure at WOT
- Only active when boost over 15psi, unlike solenoid foolers or plugs which are active all the time
- Does not create parasitic load or extra heat when inactive
- TORQUE CONVERTOR:
- Ideal replacement for tired stock torque converter
- When you purchase a BD transmission and torque converter package, you are getting a matched set that has been dyno tested together for ultimate performance, and reliability. Every transmission comes with BD's own Heavy Duty pan that adds extra fluid capacity. For towing, street or track, when it comes to a dependable transmission that will stand up to your diesel's power and torque demands, the clear choice is BD.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- TORQUEMASTER FORD 6R140 TRANS/CONVERTER PACKAGE 6.7L POWER STROKE 11-16 2WD/4WD
- Ford scanner required to update the TCM with the new solenoid code and initiate a relearn - very critical; Early 2011 model years will require 6 bolt flexplate (Approx. Pre Jan 2012 build date), see BD #1041245 or contact Ford;
- TORQUEMASTER FORD 6R140 TRANSMISSION & CONVERTER PACKAGE 6.7L POWER STROKE 2011-2016 2WD/4WD
- Trasmission & Converter Package
- Product Attributes:
- Category: Auto Trans & Converter Packages
- Engine: 6.7l Powerstroke 11-16
- Suggested Product: 1041245
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- TRANSMISSION:
- TORQUE CONVERTER:
- More clutches compared to stock and competitors
- Ideal upgrade converter for heavy tow use or higher horsepower
- Captured clutch design maintains good drivability feel
- Four surface clutch assembly doubles the OEM friction area
- Increased count of steels increases heat dissipation
- 23% increased piston area for additional clutch clamping force
- Billet bearing hub, piston and clutch retainer
- Stamp forged 1-piece cover
- Furnace-brazed pump and turbine fins
- Clutch Count: LOW REVERSE 5
- Billet intermediate shaft to handle higher power
- Upgraded input shaft is tig welded to prevent OEM weld failure in demanding applications
- Custom BD patented pressure plates increase clutch count without sacrificing part strength
- Clutch Count: FORWARD 6 (20% increase over stock)
- Clutch Count: DIRECT 6 (20% increase over stock)
- Clutch Count: INTERMEDIATE 8 (60% increase over stock)
- Clutch Count: OVERDRIVE 8 (14% increase over stock)
- Brand new valve body
- Electronic Line Pressure Controller for up to 300psi Line Pressure
- PRESSURE CONTROLLER:
- 76% more theoretical holding power
- Delivers up to 300psi line pressure at WOT
- Only active when boost over 15psi, unlike solenoid foolers or plugs which are active all the time
- Does not create parasitic load or extra heat when inactive
- When you purchase a BD transmission and torque converter package, you are getting a matched set that has been dyno tested together for ultimate performance, and reliability. Every transmission comes with BD's own Heavy Duty pan that adds extra fluid capacity. For towing, street or track, when it comes to a dependable transmission that will stand up to your diesel's power and torque demands, the clear choice is BD.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD CAC Intake Pipe Upgrade Ford 6.7L PowerStroke 2011-2016
- BD CAC Intake Pipe Upgrade Ford 6.7L PowerStroke 2011-2016 F-250/F-350
- CAC Pipe Replacement
- Product Attributes:
- Category: Intake
- Engine: 6.7l Powerstroke 11-16
- Suggested Product: 1043007
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Replaces plastic factory pipe which is prone to failure
- Black powder-coated steel charge pipe
- CNC machined aluminum throttle body adapter
- Retains factory throttle valve, no tuning required
- Maintains factory power steering fluid reservoir position
- Replace the fragile factory plastic intercooler piping that is prone to bursting due to temperature and pressure cycling with BD's steel piping and high-pressure multi-layer silicone hose boots.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2016 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
Showing 1 - 10 of 48 products
Loading...