Image
Product
Price
- BD Chevy 2 Low UnLoc - 4wd 2015-2019 2500-3500 / 2014-2019 1500 / 2015-2020 SUV
- 4wd;
- BD Chevy 2 Low UnLoc - 2015-2019 2500-3500 4wd / 2014-2019 1500 4wd / 2015-2020 SUV 4wd
- 2 Low UnLoc
- Product Attributes:
- Category: Steering
- Engine: Gasoline
- Suggested Product: 1036627
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Installation is simple, the kit plugs in under the hood
- No wire cutting or splicing
- Kit comes with an illuminated rocker switch for control and to indicate when the front axle is being overridden
- Designed to allow the operator to manually disable the front wheel drive mechanism by holding the hubs in the free (2WD) mode with the transfer case in 4WD low range
- By allowing the front wheels to be disengaged, maximum torque is available to the rear wheels
- This will also allow for sharp "All The Way Over" turns without the front axle u-joint hopping or binding
- With this kit installed, the front wheels will NOT be driven through the transfer case
- Allows to have full power and torque while in a high gear reduction applied to the rear axle(s) only
- Vehicle maneuverability is reduced while in 4WD. When the 2Low Unloc is turned on, you disable the front wheel drive mechanism allowing for full torque to be available to the rear wheels only. The front wheels will NOT be driven, delivering normal 2WD maneuverability while in low range! This will also allow for sharp "All The Way Over" turns without the front axle u-joint hopping or binding.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - GMC Yukon | V | 6162 | 8 Cyl 6.2L | 376 |
- BD Duramax High Idle Kit - Chevy 2008-2019 6.6L 2500/3500 - 2019 4500/5500/6500
- BD Duramax High Idle Kit - Chevy/GMC 2008-2019 6.6L 2500 HD / 3500 HD - 2019 Chevy 4500 HD / 5500 HD / 6500 HD
- High-Idle Kit
- Product Attributes:
- Category: High Idle
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1050346
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Easy to install
- Faster engine warm-ups
- Adjustable
- Great to use for remote starters, PTO's and extended idling applications
- 900/1200/1500/1800/2100 RPM
- Bypasses Auto Engine Off functions
- For when days are short and the nights are cold, you want your engine to heat up quicker. When you are using a PTO, or constantly idling , these are the times, when you need an elevated idle. BD's High Idle kits are easy to install and in most cases adjustable.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Chevrolet Silverado 3500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019
- CARB EO D-553-17; Includes longer studs and spacers plus all gaskets;
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019 F250/F350/F450/F550 Super Duty
- Exhaust Manifold Drivers Side
- Product Attributes:
- Category: Manifolds
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1045804
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Exhaust ports are gasket matched
- High temperature POR 15 black coated
- Includes 16 studs and spacers for BD Scorpion Kits
- Includes exhaust manifold and cross over tube gaskets
- Perfect for BD Scorpion Turbo Kit
- High-silicon ductile cast iron
- 75% thicker walls retain heat and prevents warping
- Machined thicker bolting flange
- 50 state legal
- Includes the longest stud and spacer kit that fits across all 8-cylinders
- Longer exhaust studs improve thermal durability
- Thick spacers are black oxide coated
- Designed using computation fluid dynamics
- BD focused on solving one of the Ford 6.7L common failures, the exhaust manifolds. Crafted with a heavy duty 0.275" thick-walled Hi-Silicon ductile casting, this makes these manifolds 75% thicker to combat cracking due to high exhaust temperatures. Thermal durability has been improved with longer exhaust studs and spacers plus thicker, more durable machined bolting flanges. Fully EGR compatible, BD's exhaust manifold set is the perfect replacement for reliability and peace of mind.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD Iron Horn 6.7L Cummins Turbo Kit S364SXE/80 0.91AR Dodge 2007.5-2018
- S364SXE/80 0.91AR;
- BD Iron Horn 6.7L Cummins Turbo Kit S364SXE/80 0.91AR Dodge/RAM 2007.5-2018 2500/3500
- Iron Horn Turbo Kit
- Product Attributes:
- Category: Single Turbo Performance
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1045982
- Wheel Size: S364sxe/80 0.91 Ar
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- BD Single 300 series SX-E Borg Warner turbos kits that replace your OEM VGT turbo, providing enough air for more power, response and reliability
- Comp Wheel: 64.5mm 2.54in
- Turbine Wheel: 80mm 3.15in
- A/R Ratio: 0.91
- Flow: 82 Lb./min
- Approximate rated 600hp (depending on truck configuration)
- Manifold equipped with EGR ports to retain emissions equipment.
- Turbo utilizes high flow T4 turbine housing
- The SX-E turbo was designed for performance with a 360 thrust bearing and enhanced compressor wheel and housing
- The high strength FMW Forged Milled Wheels are lighter and stronger and withstand higher wheel speeds
- Kit comes with BD's Performance Plus T4 6.7L exhaust manifold and gaskets
- No extra piping required, it drops in place for an easy, clean installation
- Reliability and power! Yes, they go together. The problematic stock Holset turbo can now be replaced with a complete performance option that reduces EGT's and high turbo drive pressures. Save your head gasket and enjoy longer engine life with a significant horsepower increase. Street and track performance from the most complete bolt-on kit on the market!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD Iron Horn 6.7L Cummins Turbo Kit S364SXE/80 1.00AR Dodge 2007.5-2018
- S364SXE/80 1.00AR;
- BD Iron Horn 6.7L Cummins Turbo Kit S364SXE/80 1.00AR Dodge/RAM 2007.5-2018 2500/3500
- Iron Horn Turbo Kit
- Product Attributes:
- Category: Single Turbo Performance
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1064264
- Wheel Size: S364sxe/80 1.00 Ar
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- BD Single 300 series SX-E Borg Warner turbos kits that replace your OEM VGT turbo, providing enough air for more power, response and reliability
- Comp Wheel: 64.5mm 2.54in
- Turbine Wheel: 80mm 3.15in
- A/R Ratio: 1.00
- Flow: 82 Lb./min
- Approximate rated 600hp (depending on truck configuration)
- Manifold equipped with EGR ports to retain emissions equipment.
- Turbo utilizes high flow T4 turbine housing
- The SX-E turbo was designed for performance with a 360 thrust bearing and enhanced compressor wheel and housing
- The high strength FMW Forged Milled Wheels are lighter and stronger and withstand higher wheel speeds
- Kit comes with BD's Performance Plus T4 6.7L exhaust manifold and gaskets
- No extra piping required, it drops in place for an easy, clean installation
- Reliability and power! Yes, they go together. The problematic stock Holset turbo can now be replaced with a complete performance option that reduces EGT's and high turbo drive pressures. Save your head gasket and enjoy longer engine life with a significant horsepower increase. Street and track performance from the most complete bolt-on kit on the market!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD Iron Horn 6.7L Cummins Turbo Kit S366SXE/80 0.91AR Dodge 2007.5-2018
- S366SXE/80 0.91AR;
- BD Iron Horn 6.7L Cummins Turbo Kit S366SXE/80 0.91AR Dodge/RAM 2007.5-2018 2500/3500
- Iron Horn Turbo Kit
- Product Attributes:
- Category: Single Turbo Performance
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1045982
- Wheel Size: S366sxe/80 0.91 Ar
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- BD Single 300 series SX-E Borg Warner turbos kits that replace your OEM VGT turbo, providing enough air for more power, response and reliability
- Comp Wheel: 66mm 2.60in
- Turbine Wheel: 80mm 3.15in
- A/R Ratio: 0.91
- Flow: 87 Lb./min
- Approximate rated 650hp (depending on truck configuration)
- Manifold equipped with EGR ports to retain emissions equipment.
- Turbo utilizes high flow T4 turbine housing
- The SX-E turbo was designed for performance with a 360 thrust bearing and enhanced compressor wheel and housing
- The high strength FMW Forged Milled Wheels are lighter and stronger and withstand higher wheel speeds
- Kit comes with BD's Performance Plus T4 6.7L exhaust manifold and gaskets
- No extra piping required, it drops in place for an easy, clean installation
- Reliability and power! Yes, they go together. The problematic stock Holset turbo can now be replaced with a complete performance option that reduces EGT's and high turbo drive pressures. Save your head gasket and enjoy longer engine life with a significant horsepower increase. Street and track performance from the most complete bolt-on kit on the market!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD 6.7L Power Stroke Screamer Turbo - Ford 2017-2019 F250/F350 /F450/F550
- BD 6.7L Power Stroke Screamer Turbo - Ford 2017-2019 F250/F350/F450/F550 Pick-up & Cab-Chassis
- Screamer Turbo
- Product Attributes:
- Category: Performance Kits
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1043008
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- 64.0mm Billet compressor wheel
- VSR high speed balanced
- Built using a brand new Garrett Turbo
- Custom mixed flow turbine (MFT) wheel with a large 65mm exducer
- Drop-in stock-appearing turbo
- Increased airflow without compromising on low end drivability
- Large 65mm 'mixed flow' turbine wheel increases turbine flow and retains efficiency
- More boost, lower drive pressure, and lower EGT's
- No tuning required and does not set engine codes
- Up to 81lb/min of airflow
- The drop-in, stock-appearing Screamer turbo for the later model Ford 6.7L Powerstroke utilizes modern turbo technology that delivers increased airflow without compromising on low end response. Boost pressure can be increased to improve horsepower potential. The Powerstroke Screamer turbo works with any "box" tuner and further improvements achieved with custom tuning. Drop-in turbo reuses the factory 2017-2019 turbo pedestal.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- Screamer Turbo Chevy/GM 6.6L L5P Duramax 2017-2024
- Screamer Turbo Chevy/GM 6.6L L5P Duramax 2017-2024 Silverado/Sierra 2500/3500
- Screamer L5P Turbo
- Product Attributes:
- Category: Single Turbo Performance
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1061825
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Increased airflow - up to 80lb/min
- Larger 66.2mm billet compressor wheel
- Larger 67mm turbine wheel
- Reduced EGTs at increased power output
- Stock appearing drop in turbo, will work with stock emissions equipment
- Up to 680hp with supporting modifications
- Includes intake horn
- BD's Screamer line of turbos offer drop-in, stock-appearing units that add an additional punch in power without major modifications to intake or exhaust systems. The L5P Screamer for 2017-up Duramax engines feature custom compressor and turbine wheels that have been designed to give you increased airflow without compromising on low end performance. Manufactured using OEM housings, the L5P Screamer turbo is machined to accept the new larger 66.2mm compressor and 67mm turbine wheels which will allow for better airflow (up to 80 lb./min) and lower exhaust gas temperatures. This turbo works best on trucks with supporting modifications such as custom tuning to maximize efficiency. With supporting modifications, the L5P Screamer can achieve up to 680hp.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - GMC Sierra 2500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- Screamer Turbo Manifold Package RAM 6.7L Cummins 2013-2018
- Direct replacement for stock turbo and exhaust manifold;
- Screamer Turbo Manifold Package RAM 6.7L Cummins 2013-2018 2500/3500
- Screamer Turbo & Manifold Package
- Product Attributes:
- Category: Stock Replacement
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1045965
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- TURBOCHARGER:
- Experience quick spool times and low drive pressures with an overall increase in performance
- 50-STATE LEGAL!
- Fully EGR compatible
- Open throat outlet flange outperforms the stock manifold
- CARB EO No D-553-5
- Drops in to the stock location
- Can support modifications up to 690HP
- Ballistic Billet 64.5mm 7+7 blade compressor wheel and Low MOI QST 70mm 12 blade turbine wheel
- The QST Turbine wheel has a 15% reduction in MOI (moment of inertia) which results in quicker turbo response
- QST Turbine blade thickness decreased by 25% allowing for higher turbine gas flow and increased efficiency
- VSR high speed balanced
- Each actuator is calibrated and tested prior to shipping
- MANIFOLD:
- Pre-drilled for pyrometer probes
- Gasket, Bolt and Spacers kits are available separately
- 6.7L performance stock replacement manifold for use with the Holset HE351 Turbo
- Cast of high silicon ductile iron to withstand extreme temperature cycling caused during DPF regeneration
- Larger porting design than others will handle any increase in power
- Thick walled casting and integral slip joint prevents cracking and exhaust leaks
- A drop-in stock installation, stock looking replacement that is anything but stock! The larger Ballistic Billet compressor wheel and our new exclusive Low MOI QST turbine wheel results in reduced backpressure, quicker response, increased efficiency and increased turbine flow compared to the competition. This results in increased maximum potential power output, right up to 690 horsepower with supporting modifications. No extra parts to install, just drop-in and enjoy the extra power potential. Perfectly paired with a pulse manifold made from high-silicon ductile iron and designed to withstand extreme temperatures and vibration. Precision slip joints allow the manifold to expand and contract, which reduces cyclic thermal fatigue and greatly increases manifold longevity.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- HE300VG Turbo Actuator - Dodge 2013-2018 6.7L Cummins
- HE300VG Turbo Actuator - RAM 2013-2018 6.7L Cummins
- Turbo Actuator
- Product Attributes:
- Category: Stock Replacement
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1045779
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- The actuator is a common failure on the HE351/HE300VG turbos
- OEM Holset replacement part
- Same actuator used on Screamer turbos
- No Core Charge!
- The actuator is a common failure on the HE351/HE300VG turbos; OEM Holset replacement part; Same actuator used on Screamer turbos; No Core Charge!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2017 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
Showing 1 - 10 of 182 products
Loading...