Shop By Product Matching "Gates"
Choose a Model for your 1999 Chevrolet
Image
Product
Price
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 23
- 584
- End 1 Inside Diameter: .48
- Material: Epdm
- End 2 Inside Diameter: .48
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
This Part Fits the Following OEM/Substitute Numbers:
10622, 15170551, 16612M, 18622, 62938, E90759
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Silverado 2500 | V | 5967 | Radiator To Reservoir | GAS | 8 Cyl 6.0L | 364 |
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 32.5
- 826
- End 1 Inside Diameter:
- 1.27
- 32
- Material: Epdm, Plastic
- Modular: No
- End 2 Inside Diameter:
- 1.27
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
15047260, 15722058, 15731692, 15751101, 22196, 26302X, 62169, 71878, 8848, C2196, E71878
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet S10 | V | - | Upper | GAS | 6 Cyl 4.3L | 262 |
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 23.8
- 605
- End 1 Inside Diameter:
- .71
- 18
- Material: Epdm
- End 2 Inside Diameter:
- .71
- 18
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
This Part Fits the Following OEM/Substitute Numbers:
11707, 15978377, 18139L, 19707, 63504, 8159783770, 88389, E88389
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet S10 | V | - | Heater To Engine | GAS | 6 Cyl 4.3L | 262 |
- Preferred Pulley
- DriveAlign Premium OE Pulley
- Product Attributes:
- Contact Surface: Smooth/backside
- Pulley Quantity: 1
- Pulley 1 Groove Quantity: 0
- Pulley 1 Outside Diameter (mm): 90
- Pulley 1 Flanged: No
- Bearing Bore Inside Diameter: 17
- Pulley 1 Width (mm): 31
- Material: Steel
-
Features:
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
- DriveAlign Idler Pulleys provide OE-quality fit to passenger cars and light trucks, performing as a locked center tensioning pulley, an automatic belt tensioner pulley or an idler pulley.
This Part Fits the Following OEM/Substitute Numbers:
12555609, 12580771, 12669569, 36299, 49154, 8010, 8016, 900401, 900401A
Additional Fitment Information:
| Vehicle | Block | CC | Fuel Type | Engine | CID |
|---|---|---|---|---|---|
| 1999 - Chevrolet Silverado 2500 | V | 5328 | GAS | 8 Cyl 5.3L | 325 |
- Molded Heater Hose
- Product Attributes:
- Branch Quantity: 0
- Molded: Yes
- Centerline Length:
- 123
- 4.83
- End 1 Inside Diameter:
- .25
- 6
- Material: Epdm
- End 2 Inside Diameter:
- .25
- 6
- Quick Connect Fitting Quantity: 0
-
Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. It can be used for coolant, water and air applications, also approved for marine applications.
This Part Fits the Following OEM/Substitute Numbers:
10623, 12570528, 14754S, 18623, 86504, B86504
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Silverado 1500 | V | - | Throttle Body To Engine | GAS | 8 Cyl 4.8L | 294 |
- W/130A. Alt.
- Accessory Belt Drive Kit (Standard)
- Product Attributes:
- Idler Pulley 1 Part Number: 38001
- Belt 1 Part Number: K060930
- Outside Circumference:
- 2377
- 93.585
- Tensioner Assembly Part Number: 38158
- Belt Top Width:
- .807
- 20
-
Features:
- Designed for convenience, easy parts sourcing and reduced customer comebacks
- Includes serpentine belt with premium EPDM construction, tensioner, applicable idler pulleys and applicable tensioner hardware
- Meets or exceeds OE standards in form, function and fit
- NOTE: Kit contents vary depending on specific needs of vehicle kit application
- Complete Serpentine Kits make it easy to restore the entire accessory belt drive system. Eliminate customer comebacks by fixing the vehicle the first time by servicing the entire serpentine drive. Neglecting to replace the tensioner and pulley(s) at the same time you replace the belt can ultimately shorten the life of the belt as well as other front-end accessory components. Each kit contains an OE-equivalent belt, tensioner, idler pulley and necessary hardware with installation instructions and tech tips for easy, accurate installation for virtually every vehicle on the road today.
This Part Fits the Following OEM/Substitute Numbers:
90K-38158B, ACK060930, D60930K1, DBK060930, K49275B, LV999033C
Additional Fitment Information:
| Vehicle | Block | CC | Fuel Type | Engine | CID |
|---|---|---|---|---|---|
| 1999 - Chevrolet Silverado 1500 | V | 5328 | GAS | 8 Cyl 5.3L | 325 |
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 19.1
- 485
- End 1 Inside Diameter:
- 1.27
- 32
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.27
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
10238922, 10306075, 10306705, 10352409, 10422115, 22361, 26351X, 62326, 71949, 88894136, 88894251, 88895497, 88897267, 89023429, 8994, D71949
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Venture | V | - | Upper | GAS | 6 Cyl 3.4L | 207 |
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 1214
- 47.8
- End 1 Inside Diameter:
- 1.27
- 32
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.27
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
10379176, 15041305, 15045504, 15057981, 15076028, 15078028, 15179498, 22436, 26390X, 62262, 62634, 71989, 9069, C2436, D92675, E71989
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Silverado 1500 | V | - | Upper | GAS | 8 Cyl 4.8L | 294 |
- Optional Hose
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 21.2
- 538
- End 1 Inside Diameter:
- 1.25
- 32
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.25
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Monte Carlo | V | - | Upper | GAS | 6 Cyl 3.1L | 189 |
- Molded Coolant Hose
- Product Attributes:
- Branch Quantity: 0
- Contains Spring: No
- Molded: Yes
- Centerline Length:
- 21.2
- 538
- End 1 Inside Diameter:
- 1.25
- 32
- Material: Epdm
- Modular: No
- End 2 Inside Diameter:
- 1.25
- 32
- Quick Connect Fitting Quantity: 0
-
Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube
- synthetic fiber knit reinforcement
- heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
- Our Molded Coolant Hoses are manufactured to fit upper, lower, bypass, heater and other coolant applications with OEM-quality specifications, saving you time, money and energy from going to your OE dealer for radiator hose replacements. Gates' molded coolant hose line is the most comprehensive line on the replacement market.
This Part Fits the Following OEM/Substitute Numbers:
10285951, 10401339, 10401999, 10421339, 22344, 26346X, 8977, C2344, F11072, PCH114840
Additional Fitment Information:
| Vehicle | Block | CC | Position | Fuel Type | Engine | CID |
|---|---|---|---|---|---|---|
| 1999 - Chevrolet Monte Carlo | V | 3800 | Upper | GAS | 6 Cyl 3.8L | 231 |
Showing 1 - 10 of 402 products
Loading...