Shop By Product Matching "MSD"
Choose a Model for your 1985 Ford
Image
Product
Price
- Direct Replacement; 5.6 mH Inductance; 44000 Max Voltage; 220 ma Peak Current; 300 uS Spark Duration; 100:1 Turns Ratio; Red; Single;CARB E.O. D-40-37 0.68 ohms Primary Resistance/4.8k ohms Secondary Resistance
- Blaster TFI Ignition Coil; Direct Replacement; 5.6 mH Inductance; 44000 Max Voltage; 220 ma Peak Current; 300 uS Spark Duration; 100:1 Turns Ratio; Red; Single;
- Blaster TFI Ignition Coil
- Product Attributes:
- Spark Duration: 300 Us
- WARNING CA Proposition 65: Yes
- Inductance: 5.6 Mh
- Maximum Voltage: 44000
- Peak Current: 220 Ma
- Primary Resistance: .680 Ohms
- Secondary Resistance: 4.8k Ohms
-
Features:
- Direct performance replacement for Ford TFI coil
- 85:1 turns ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
- CARB E.O. Approved
- Top off your Ford ignition system with these great new replacement coils. The Blaster TFI has MSD performance in factory-style housings! The MSD Blaster TFI Coil is designed to produce increased voltage and energy over the stock Ford TFI Coil. To get even more ignition performance, install an MSD ignition Control with a PN 8874 Harness for a direct plug-in installation.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Ranger | L | 1989 | 4 Cyl 2.0L | 122 |
- Direct Replacement; 5.6 mH Inductance; 44000 Max Voltage; 220 ma Peak Current; 300 uS Spark Duration; 100:1 Turns Ratio; Red; Single;CARB E.O. D-40-37 0.68 ohms Primary Resistance/4.8k ohms Secondary Resistance
- Blaster TFI Ignition Coil; Direct Replacement; 5.6 mH Inductance; 44000 Max Voltage; 220 ma Peak Current; 300 uS Spark Duration; 100:1 Turns Ratio; Red; Single;
- Blaster TFI Ignition Coil
- Product Attributes:
- Spark Duration: 300 Us
- WARNING CA Proposition 65: Yes
- Inductance: 5.6 Mh
- Maximum Voltage: 44000
- Peak Current: 220 Ma
- Primary Resistance: .680 Ohms
- Secondary Resistance: 4.8k Ohms
-
Features:
- Direct performance replacement for Ford TFI coil
- 85:1 turns ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
- CARB E.O. Approved
- Top off your Ford ignition system with these great new replacement coils. The Blaster TFI has MSD performance in factory-style housings! The MSD Blaster TFI Coil is designed to produce increased voltage and energy over the stock Ford TFI Coil. To get even more ignition performance, install an MSD ignition Control with a PN 8874 Harness for a direct plug-in installation.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Ranger | L | 1989 | 4 Cyl 2.0L | 122 |
- 8.5mm; Fits Engines w/Late-model Type HEI Distributor Caps; Includes [8] 90 Degree Boots/Terminal Ends; Red
- Universal Spark Plug Wire Set; 8.5mm; Fits Engines w/Late-model Type HEI Distributor Caps; Includes [8] 90 Degree Boots/Terminal Ends; Red;
- Universal Spark Plug Wire Set
- Product Attributes:
- Boot Type: 90 Degree
- Engine: Universal 8 Cylinder
-
Features:
- Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
- Distributor Cap - Boots and Terminals Included
- Includes Mini-Stripper-Crimper For Factory Style Crimps
- Size Includes [8] 90 Degree Boots/Terminal Ends
- Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the Straight Multi-angle spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. Its a little more work, but in the end it will be worth it.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | 351 |
- 8.5mm; Fits Engines w/Late-model Type HEI Distributor Caps; Includes [8] 90 Degree Boots/Terminal Ends; Red
- Universal Spark Plug Wire Set; 8.5mm; Fits Engines w/Late-model Type HEI Distributor Caps; Includes [8] 90 Degree Boots/Terminal Ends; Red;
- Universal Spark Plug Wire Set
- Product Attributes:
- Boot Type: 90 Degree
- Engine: Universal 8 Cylinder
-
Features:
- Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
- Distributor Cap - Boots and Terminals Included
- Includes Mini-Stripper-Crimper For Factory Style Crimps
- Size Includes [8] 90 Degree Boots/Terminal Ends
- Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the Straight Multi-angle spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. Its a little more work, but in the end it will be worth it.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | 351 |
- 8.5mm; Fits Ford Small Block Engines; HEI Boots; Black
- Custom Spark Plug Wire Set; 8.5mm; Fits Ford Small Block Engines; HEI Boots; Black;
- Custom Spark Plug Wire Set
- Product Attributes:
- WARNING CA Proposition 65: No
- Boot Type: Multi-angle
- Engine: Oem
- Engine Make/Size: Oem
-
Features:
- Custom Fit For Make And Model Listed
- Wires Are Pre-Cut To Exact Specifications
- Bolt-on Performance
- Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 - 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. The MSDs 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor. The MSDs 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | Windsor | 351 |
- 8.5mm; Fits Ford Small Block Engines; HEI Boots; Black
- Custom Spark Plug Wire Set; 8.5mm; Fits Ford Small Block Engines; HEI Boots; Black;
- Custom Spark Plug Wire Set
- Product Attributes:
- WARNING CA Proposition 65: No
- Boot Type: Multi-angle
- Engine: Oem
- Engine Make/Size: Oem
-
Features:
- Custom Fit For Make And Model Listed
- Wires Are Pre-Cut To Exact Specifications
- Bolt-on Performance
- Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 - 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. The MSDs 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor. The MSDs 8.5mm spark plug terminals feature Dual Crimp terminals. As the name implies, the terminals feature two crimps; one for the sleeve of the wire and another separate crimp to grasp the conductor.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | 351 |
- Black Super Conductor; 8.5mm; Fits 8 Cyl. Late Model HEI Caps [Ford Duraspark Or MSD Cap-A-Dapt]; Includes: Wires/90 Degree Boots/Terminals
- Universal Spark Plug Wire Set; Black Super Conductor; 8.5mm; Fits 8 Cyl. Late Model HEI Caps [Ford Duraspark Or MSD Cap-A-Dapt]; Includes: Wires/90 Degree Boots/Terminals;
- Universal Spark Plug Wire Set
- Product Attributes:
- Boot Type: 90 Degree
- Engine: Universal 8 Cylinder
- Engine Make/Size: Universal 8 Cylinder
-
Features:
- Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
- Distributor Cap - Boots and Terminals Included
- Includes Mini-Stripper-Crimper
- Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. Its a little more work, but in the end it will be worth it.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | Windsor | 351 |
- Black Super Conductor; 8.5mm; Fits 8 Cyl. Late Model HEI Caps [Ford Duraspark Or MSD Cap-A-Dapt]; Includes: Wires/90 Degree Boots/Terminals
- Universal Spark Plug Wire Set; Black Super Conductor; 8.5mm; Fits 8 Cyl. Late Model HEI Caps [Ford Duraspark Or MSD Cap-A-Dapt]; Includes: Wires/90 Degree Boots/Terminals;
- Universal Spark Plug Wire Set
- Product Attributes:
- Boot Type: 90 Degree
- Engine: Universal 8 Cylinder
- Engine Make/Size: Universal 8 Cylinder
-
Features:
- Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
- Distributor Cap - Boots and Terminals Included
- Includes Mini-Stripper-Crimper
- Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. Its a little more work, but in the end it will be worth it.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | 351 |
- Steel Gear For Factory Roller Cam; w/Module;O.E.M. Replacement Part
- Pro-Billet Distributor; Steel Gear For Factory Roller Cam; w/Module;
- Pro-Billet Distributor
- Product Attributes:
- Distributor Type: Hei/breakerless
- WARNING CA Proposition 65: Yes
- Engine Make/Size: Ford 351w
-
Features:
- Drop in billet replacement for late model Ford TFI 5.8L dist.
- Supplied w/steel gear to work w/factory roller camshafts
- Factory style ignition module connector accepts factory wiring
- CNC machined billet aluminum housing and billet aluminum base
- QPQ coated polished steel shaft
- guided by sealed ball bearings
- Supplied w/Late Model Distributor Cap And Rotor
- Legal to install in all 50 states
- When you start making serious power with your EFI Ford, the stock distributor shaft is one of the weak links of the engine. These Pro-Billet models answer the need for an affordable replacement in a strong and great looking package. Each distributor starts as a solid billet that is secured into a state-of-theart Computer Numerical Control (CNC) machine where it is transformed into a precision housing. Inside each housing there is a sealed ball bearing at the top of the shaft. This design is responsible for accurately guiding the oversized polished steel shaft throughout the entire rpm range of your engine. The shaft is also QPQ-coated for friction reduction and corrosion resistance. The Pro-Billet Distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place! Each model is supplied with a high-quality cap with brass terminals for full spark delivery, heavy-duty rotor and a special gear to work with the factory camshafts.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1985 - Ford Bronco | V | 5753 | 8 Cyl 5.8L | Windsor | 351 |
- Steel Gear For Factory Roller Cam; w/Module;O.E.M. Replacement Part
- Pro-Billet Distributor; Steel Gear For Factory Roller Cam; w/Module;
- Pro-Billet Distributor
- Product Attributes:
- Distributor Type: Hei/breakerless
- WARNING CA Proposition 65: Yes
- Engine Make/Size: Ford 351w
-
Features:
- Drop in billet replacement for late model Ford TFI 5.8L dist.
- Supplied w/steel gear to work w/factory roller camshafts
- Factory style ignition module connector accepts factory wiring
- CNC machined billet aluminum housing and billet aluminum base
- QPQ coated polished steel shaft
- guided by sealed ball bearings
- Supplied w/Late Model Distributor Cap And Rotor
- Legal to install in all 50 states
- When you start making serious power with your EFI Ford, the stock distributor shaft is one of the weak links of the engine. These Pro-Billet models answer the need for an affordable replacement in a strong and great looking package. Each distributor starts as a solid billet that is secured into a state-of-theart Computer Numerical Control (CNC) machine where it is transformed into a precision housing. Inside each housing there is a sealed ball bearing at the top of the shaft. This design is responsible for accurately guiding the oversized polished steel shaft throughout the entire rpm range of your engine. The shaft is also QPQ-coated for friction reduction and corrosion resistance. The Pro-Billet Distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place! Each model is supplied with a high-quality cap with brass terminals for full spark delivery, heavy-duty rotor and a special gear to work with the factory camshafts.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | Engine Version | CID |
|---|---|---|---|---|---|
| 1985 - Ford LTD | V | 5753 | 8 Cyl 5.8L | Modified | 351 |
Showing 1 - 10 of 44 products
Loading...