Image
Product
Price
- BD E-PAS Positive Air Shut-Off 6.7L Powerstroke Ford 2011-2019
- Plug-In Install;
- BD E-PAS Positive Air Shut-Off 6.7L Powerstroke Ford 2011-2019 F250/F350/F450/F550
- Electronic Positive Air Shutdown
- Product Attributes:
- Category: Electronic Emergency Engine Shutdown
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1057932
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Emergency Engine Shutdown
- Easily removed for truck lease returns
- Over speed shut down control utilizing built in Intake Air control valve
- Safely shuts your engine down if over speeding
- Can be installed in less than 1.5 hours
- Factory plug in connections and wiring harness
- Save 3 hours installation labor over mechanical systems
- Does not set ECM Trouble codes
- Automatically resets after shut down
- Only the switch needs a tool to install
- Like a fire extinguisher in your house, or an earthquake kit, it's always better to be prepared. Although rare, Diesel Engine Runaway is caused when external hydrocarbons are drawn into the engine and can cause over speeding and catastrophic engine failure. Life, limb and your vehicle are put in jeopardy. BD Diesel Performance has you covered should the worst happen with our Electronic Positive Air Shutdown (E-PAS) units by cutting the intake air supply to the cylinders and safely shutting down the engine. The E-PAS controls the electronic throttle body in the intake manifold found on most late model diesel engines by closing it to shut off the air supply in emergency situations. The E-PAS can be easily installed in less than 1.5 hours with factory plug-in connectors and premade wiring harnesses. Automatically resets itself after shutdown and can be easily removed for truck lease returns.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- Injector - Chevy 6.6L Duramax 2011-2016 LML Stock Replacement
- Individual injector; LML;
- Injector - Chevy/GMC 6.6L Duramax 2011-2016 LML Stock Replacement
- Replacement Injector
- Product Attributes:
- Category: Stock Injectors
- Engine: Duramax 6.6l 11-16 Lml-lgh
- Suggested Product: 1045830
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Bosch Individual exchange injectors
- Bosch's Remanufactured Diesel Injectors are produced at the same Bosch facility as the new diesel injectors. All wearable parts and critical components are replaced with genuine Bosch parts, and the latest original equipment production technology is used. Bosch remanufactured injectors include all OE updates, so they can often be superior to the OE injectors that they replace.
-
Suggested Purchase Quantity: 8
- Most jobs typically require 8 of this item.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - GMC Sierra 3500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- BD Track Bar Bracket Ford F-250/F-350 SuperDuty 4wd 2008-2022
- 4wd; Lowers track bar mounting point by 2-inches;
- BD Track Bar Bracket Ford F-250/F-350 Superduty 4wd 2008-2022 (Gas & Diesel)
- Track Bar Bracket
- Product Attributes:
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1032110
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Ideal for 2-inch or 2.5-inch levelling kits
- Lowers track bar mounting point by 2-inches
- Corrects steering geometry on lifted vehicles
- Improves bump steer in levelled trucks
- High strength cast iron with ADI heat treat process for maximum strength
- Can be combined with BD 1032110/1032111 Track Bars for adjustability or larger lift height
- Common leveling and lift kits pull the trackbar out of position, affecting ride and steering quality, as well as axle position with respect to the body and frame. BD's track bar bracket relocates the pivot point 2-inch down lower down, offsetting the effect of the lift kit by bringing the trackbar assembly down into the factory position and fixing common steering and tracking issues. The BD track bar bracket is designed with high strength, ADI heat-treated cast iron for maximum strength and provides a strong reliable upgrade.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD End Links - Chevy/GMC 2001-2019 2500 HD / 3500HD Silverado/Sierra
- BD End Links (Pair) - Chevy/GMC 2001-2019 2500 HD / 3500HD Silverado/Sierra
- End Links Set
- Product Attributes:
- Category: Steering
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1032150
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- 1" longer than factory to accommodate upgraded tie rods, and/or leveling kits
- High-strength through bolt design
- OEM style bushing shape for articulation and durability
- Durable Polyurethane bushings
- Installed in approximately 1 hour
- Whether making necessary repairs or upgrades to your steering setup, or running stock to 2" lift or leveling kits, BD's NEW sway bar end links for 2001-2019 Chevy 2500/3500's are your best option to ensure your steering is tight and on the level! Longer, high-strength through bolt design sway bar end links accommodate larger tie rods and leveling kits. Durable polyurethane bushings are designed in the OEM profile to maintain articulation and durability. Leveling kits and lift kits will pull the swaybar out of position, compromising steering geometry. Additionally upgrading tie rods can also cause swaybar interference issues. BD's durable, longer, high-strength, sway bar end links correct sway bar angles and give you the additional clearance you need for those upgraded tie rods. Tighten up the sway bar assembly on your truck and ensure your truck's control is direct and confidence inspiring while avoiding that front end "clunk" that comes with worn out bushings.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Chevrolet Silverado 3500 HD | V | 5967 | 8 Cyl 6.0L | 364 |
- BD Duramax High Idle Kit - Chevy 2008-2019 6.6L 2500/3500 - 2019 4500/5500/6500
- BD Duramax High Idle Kit - Chevy/GMC 2008-2019 6.6L 2500 HD / 3500 HD - 2019 Chevy 4500 HD / 5500 HD / 6500 HD
- High-Idle Kit
- Product Attributes:
- Category: High Idle
- Engine: Duramax 6.6l 17-up L5p
- Suggested Product: 1050346
- Make: Chevy/gm
- Prop 65 (C, R or CR): Cr
-
Features:
- Easy to install
- Faster engine warm-ups
- Adjustable
- Great to use for remote starters, PTO's and extended idling applications
- 900/1200/1500/1800/2100 RPM
- Bypasses Auto Engine Off functions
- For when days are short and the nights are cold, you want your engine to heat up quicker. When you are using a PTO, or constantly idling , these are the times, when you need an elevated idle. BD's High Idle kits are easy to install and in most cases adjustable.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - GMC Sierra 2500 HD | V | 6599 | 8 Cyl 6.6L | 403 |
- BD Cummins Killer Frost Plug Plate - Dodge/RAM 2003-2018 5.9L/6.7L
- BD Cummins Killer Frost Plug Plate - Dodge/RAM 2003-2018 5.9L/6.7L Cummins
- Killer Frost Plug Plate
- Product Attributes:
- Category: Killer Frost Plug Plate
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1050333
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- Works with the frost plug in place, blown out, or leaking
- No need to punch the old frost plug out
- Utilizes one large #333 O-ring
- Works with and without a TCC crossover tube
- Five flanged head bolts to keep the coolant contained
- 6.7L require the bellhousing support bracket to be removed
- Perfect time to install one is when the transmission is removed!
- The coolant pressure inside the engine block can reach 70+psi at high rpm before the thermostat fully opens. This will cause a corroded frost plug to leak. The BD rear frost plug is able to be seal the leak without the need to hammer out the old frost plug. We recommend installing the rear frost plug plate when the transmission is removed. The plate can be installed with the transmission in place, however the surface finish on the back of the motor is critical and must be checked prior to use.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- X-Flow Air Intake Heater Kit - Dodge 2008-2018 6.7L Cummins
- For Use with X Intake Elbows;
- X-Flow Air Intake Heater Kit - Dodge/RAM 2008-2018 6.7L Cummins
- X-Flow Air Intake Heater Kit
- Product Attributes:
- Category: Intake
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1041561
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- Heater for BD Intake Horns (p/n 1041560 / 1041561 / 1041566) when installed with Intake Open Grid (p/n 1041562 / 1041564)
- Aids cool and cold weather starting
- Connects to stock grid heater wire
- When installing he X-Flow Intake and Open Grid Plate in a Cummins, the factory grid heater is removed. By adding the BD X-Flow Air Intake Heater Kit to your X-Flow Intake you can take advantage of quicker, cleaner cold starts.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD 6.7L Cummins Open Grid X-Intake Dodge 2007.5-2018 2500/3500
- Eliminates Cold Weather Intake Air Heater;
- BD 6.7L Cummins Open Grid X-Intake Dodge/RAM 2007.5-2018 2500/3500
- X-Intake Air Grid
- Product Attributes:
- Category: Intake
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1041563
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- Eliminates restrictive stock cold weather intake air heater grid
- 35% larger opening cools EGT's and improves turbo response
- For cold weather operation, optional Intake Heater available for use with BD 6.7L X-Flow Intake horns
- Bolt the X-Flow Intake Elbow to our 6.7L Intake Open Grid for additional flow and performance! By removing the grid heating element, the Open Grid Plate increases the opening by 35%, eliminating the restrictive bottle neck found in the factory intake.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019
- CARB EO D-553-17; Includes longer studs and spacers plus all gaskets;
- BD 6.7L Powerstroke Driver's Side Exhaust Manifold Kit - Ford 2011-2019 F250/F350/F450/F550 Super Duty
- Exhaust Manifold Drivers Side
- Product Attributes:
- Category: Manifolds
- Engine: 6.7l Powerstroke 17-up
- Suggested Product: 1045804
- Make: Ford
- Prop 65 (C, R or CR): Cr
-
Features:
- Exhaust ports are gasket matched
- High temperature POR 15 black coated
- Includes 16 studs and spacers for BD Scorpion Kits
- Includes exhaust manifold and cross over tube gaskets
- Perfect for BD Scorpion Turbo Kit
- High-silicon ductile cast iron
- 75% thicker walls retain heat and prevents warping
- Machined thicker bolting flange
- 50 state legal
- Includes the longest stud and spacer kit that fits across all 8-cylinders
- Longer exhaust studs improve thermal durability
- Thick spacers are black oxide coated
- Designed using computation fluid dynamics
- BD focused on solving one of the Ford 6.7L common failures, the exhaust manifolds. Crafted with a heavy duty 0.275" thick-walled Hi-Silicon ductile casting, this makes these manifolds 75% thicker to combat cracking due to high exhaust temperatures. Thermal durability has been improved with longer exhaust studs and spacers plus thicker, more durable machined bolting flanges. Fully EGR compatible, BD's exhaust manifold set is the perfect replacement for reliability and peace of mind.
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ford F-350 Super Duty | V | 6651 | 8 Cyl 6.7L | 406 |
- BD Iron Horn 6.7L Cummins Turbo Kit S363SXE/80 0.91AR Dodge 2007.5-2018
- S363SXE/80 0.91AR;
- BD Iron Horn 6.7L Cummins Turbo Kit S363SXE/80 0.91AR Dodge/RAM 2007.5-2018 2500/3500
- Iron Horn Turbo Kit
- Product Attributes:
- Category: Single Turbo Performance
- Engine: 6.7l Cummins 13-18
- Suggested Product: 1064264
- Wheel Size: S363sxe/80 0.91 Ar
- Make: Dodge
- Prop 65 (C, R or CR): Cr
-
Features:
- BD Single 300 series SX-E Borg Warner turbos kits that replace your OEM VGT turbo, providing enough air for more power, response and reliability
- Comp Wheel: 63mm 2.48in
- Turbine Wheel: 80mm 3.15in
- A/R Ratio: 0.91
- Flow: 79 Lb./min
- Approximate rated 550hp (depending on truck configuration)
- Manifold equipped with EGR ports to retain emissions equipment.
- Turbo utilizes high flow T4 turbine housing
- The SX-E turbo was designed for performance with a 360 thrust bearing and enhanced compressor wheel and housing
- The high strength FMW Forged Milled Wheels are lighter and stronger and withstand higher wheel speeds
- Kit comes with BD's Performance Plus T4 6.7L exhaust manifold and gaskets
- No extra piping required, it drops in place for an easy, clean installation
- Reliability and power! Yes, they go together. The problematic stock Holset turbo can now be replaced with a complete performance option that reduces EGT's and high turbo drive pressures. Save your head gasket and enjoy longer engine life with a significant horsepower increase. Street and track performance from the most complete bolt-on kit on the market!
Additional Fitment Information:
| Vehicle | Block | CC | Engine | CID |
|---|---|---|---|---|
| 2011 - Ram 3500 | L | - | 6 Cyl 6.7L | 408 |
Showing 1 - 10 of 219 products
Loading...